ganeshreddyk at gmail
Nov 3, 2011, 10:41 AM
Post #1 of 1
(235 views)
Permalink
|
|
Regarding smux peer command in quagga ripngd
|
|
Hi,
Regarding “smux peer” command support in quagga daemons observation:--
Even though OID’s are mentioned for all Quagga routing protocols in
the quagga document,It is observed in ripngd that, 'smux peer' commnd
is not recognizing and throwing error.
And also I verified in quagga 0.99.18 source code that ripngd is not
containing “smux peer” registration part is not available.
Is ripng not supporting smux configuration? Any issues in this regard
Thanks,
Ganesh
Reference:--
16.3 MIB and command reference
The following OID numbers are used for the interprocess communication
of snmpd and the
Quagga daemons. Sadly, SNMP has not been implemented in all daemons yet.
(OIDs below .iso.org.dod.internet.private.enterprises)
zebra .1.3.6.1.4.1.3317.1.2.1 .gnome.gnomeProducts.zebra.zserv
bgpd .1.3.6.1.4.1.3317.1.2.2 .gnome.gnomeProducts.zebra.bgpd
ripd .1.3.6.1.4.1.3317.1.2.3 .gnome.gnomeProducts.zebra.ripd
ospfd .1.3.6.1.4.1.3317.1.2.5 .gnome.gnomeProducts.zebra.ospfd
ospf6d .1.3.6.1.4.1.3317.1.2.6 .gnome.gnomeProducts.zebra.ospf6d
The following OID numbers are used for querying the SNMP daemon by a client:
zebra .1.3.6.1.2.1.4.24 .iso.org.dot.internet.mgmt.mib-2.ip.ipForward
ospfd .1.3.6.1.2.1.14 .iso.org.dot.internet.mgmt.mib-2.ospf
bgpd .1.3.6.1.2.1.15 .iso.org.dot.internet.mgmt.mib-2.bgp
ripd .1.3.6.1.2.1.23 .iso.org.dot.internet.mgmt.mib-2.rip2
ospf6d .1.3.6.1.3.102 .iso.org.dod.internet.experimental.ospfv3
The following syntax is understood by the Quagga daemons for configuring SNMP:
smux peer oid [Command]
no smux peer oid [Command]
smux peer oid password [Command]
no smux peer oid password [Command]
Thanks,
Ganesh
From: Bv Rajesh-B35907
Sent: Monday, September 19, 2011 5:18 PM
To: Chaithanya Sai-B38515; Kumar Varun-B36461; Pothuganti
Sridhar-B38513; Reddy Ganesh-B38514; Reddy P Ravi Kanth-B38528;
Syrigapu Yugandhar-B38512
Subject: FW: Quagga SNMP Support
Hi All,
As discussed on Friday, we need to add code to configure SMUX agent in
your respective daemons as listed below.
This call need to happen in your Init Function.
Pl. remember to add this part of your check-ins.
Varun,
I hope you have added respective configuration in NetSNMP, in factory
default condition too. Pl. ensure this.
Regards,
--Rajesh
From: Kumar Varun-B36461
Sent: Friday, September 09, 2011 10:46 AM
To: Bv Rajesh-B35907; Reddy P Ravi Kanth-B38528; Chaithanya
Sai-B38515; Syrigapu Yugandhar-B38512; Reddy Ganesh-B38514; Pothuganti
Sridhar-B22289
Subject: Quagga SNMP Support
Hi All,
As part of the SNMP support in Quagga , following default
configuration need to be add in all the
quagga configuration files.
1) In ospfd.conf
smux peer .1.3.6.1.4.1.3317.1.2.5 quagga_ospfd
2) In ripd.conf
smux peer .1.3.6.1.4.1.3317.1.2.3 quagga_ripd
3) In bgpd.conf
smux peer .1.3.6.1.4.1.3317.1.2.2 quagga_bgpd
4) In zebra.conf
smux peer .1.3.6.1.4.1.3317.1.2.1 quagga_zebra
Thanks
Varun Kumar.C
_______________________________________________
Quagga-users mailing list
Quagga-users [at] lists
http://lists.quagga.net/mailman/listinfo/quagga-users
|
