hidden at xmission
Jun 6, 2011, 9:16 AM
Post #3 of 3
(887 views)
Permalink
|
Robert:
Yes, this is possible. semi-edited output below:
FCX648SHPOE Router#
FCX648SHPOE Router#conf t
FCX648SHPOE Router(config)#int e 1/1/25 to 1/1/28
FCX648SHPOE Router(config-mif-1/1/25-1/1/28)#link-agg act
FCX648SHPOE Router(config-mif-1/1/25-1/1/28)#exit
SYSLOG: <14>0d00h03m29s:FCX648SHPOE Router Trunk: Group (1/1/25, 1/1/26,
1/1/27,
1/1/28) created by 802.3ad link-aggregation module.
FCX648SHPOE Router#
SYSLOG: <14>0d00h03m32s:FCX648SHPOE Router System: Interface ethernet
1/1/25, state up
SYSLOG: <14>0d00h03m32s:FCX648SHPOE Router System: Logical link on interface
ethernet 1/1/25 is up.
SYSLOG: <14>0d00h03m32s:FCX648SHPOE Router System: Interface ethernet
1/1/26, state up
SYSLOG: <14>0d00h03m32s:FCX648SHPOE Router System: Logical link on interface
ethernet 1/1/26 is up.
SYSLOG: <14>0d00h03m32s:FCX648SHPOE Router System: Interface ethernet
1/1/27, state up
SYSLOG: <14>0d00h03m32s:FCX648SHPOE Router System: Logical link on interface
ethernet 1/1/27 is up.
SYSLOG: <14>0d00h03m32s:FCX648SHPOE Router System: Interface ethernet
1/1/28, state up
SYSLOG: <14>0d00h03m32s:FCX648SHPOE Router System: Logical link on interface
ethernet 1/1/28 is up.
FCX648SHPOE Router(config)#
FCX648SHPOE Router(config)#trunk e 1/1/25 to 1/1/28
FCX648SHPOE Router(config-trunk-1/1/25-1/1/28)#config-trunk-ind
FCX648SHPOE Router(config-trunk-1/1/25-1/1/28)#dis e 1/1/25
SYSLOG: <14>0d00h03m42s:FCX648SHPOE Router System: Interface ethernet
1/1/25, state down
FCX648SHPOE Router(config-trunk-1/1/25-1/1/28)#show trunk
Configured trunks:
Trunk ID: 25
Hw Trunk ID: 1
Ports_Configured: 4
Primary Port Monitored: Individually
Ports 1/1/25 1/1/26 1/1/27 1/1/28
Port Names none none none none
Port_Status disable enable enable enable
Monitor off off off off
Rx Mirr Port N/A N/A N/A N/A
Tx Mirr Port N/A N/A N/A N/A
Monitor Dir N/A N/A N/A N/A
Operational trunks:
Trunk ID: 25
Hw Trunk ID: 1
Duplex: Full
Speed: 1G
Tag: No
Priority: level0
Active Ports: 3
Ports 1/1/25 1/1/26 1/1/27 1/1/28
Link_Status down active active active
port_state Disable Forward Forward Forward
LACP_Status down ready ready ready
FCX648SHPOE Router(config-trunk-1/1/25-1/1/28)#
-----Original Message-----
From: foundry-nsp-bounces [at] puck
[mailto:foundry-nsp-bounces [at] puck] On Behalf Of Robert Hass
Sent: Monday, June 06, 2011 3:46 AM
To: foundry-nsp [at] puck
Subject: [f-nsp] Disable one port within trunk group
Hi
I would like to disable 1 GE port which is assigned to trunk group
(LAG currently consist 4 GE ports) but software reject entering into
interface level:
telnet [at] lab-fc(config)#int e1/1/5
Error - cannot configure secondary ports of a trunk
Can I do this some way ?
My configuration:
interface ethernet 1/1/3
port-name GE to TEST-6500
load-interval 30
spanning-tree 802-1w admin-pt2pt-mac
no flow-control
link-aggregate configure key 40000
link-aggregate active
pvst-mode
!
interface ethernet 1/1/4
port-name GE to TEST-6500
link-aggregate configure key 40000
link-aggregate active
pvst-mode
!
interface ethernet 1/1/5
port-name GE to TEST-6500
link-aggregate configure key 40000
link-aggregate active
pvst-mode
!
interface ethernet 1/1/6
port-name GE to TEST-6500
link-aggregate configure key 40000
link-aggregate active
pvst-mode
!
telnet [at] lab-fc#sh ver
Copyright (c) 1996-2010 Brocade Communications Systems, Inc.
UNIT 1: compiled on Sep 20 2010 at 22:46:47 labeled as FCXR07200
(5591177 bytes) from Secondary FCXR07200.bin
SW: Version 07.2.00T7f3
Boot-Monitor Image size = 369292, Version:07.1.00T7f5 (grz07100)
HW: Stackable FCX624
Robert
_______________________________________________
foundry-nsp mailing list
foundry-nsp [at] puck
http://puck.nether.net/mailman/listinfo/foundry-nsp
_______________________________________________
foundry-nsp mailing list
foundry-nsp [at] puck
http://puck.nether.net/mailman/listinfo/foundry-nsp
|
