Mailing List Archive: MythTV: Users

lirc incompatible with new dev/input device?

Index | Next | Previous | View Threaded

support at ocg

Jan 17, 2008, 8:44 AM

Post #1 of 3 (270 views)
Permalink

lirc incompatible with new dev/input device?

I've been working through some newly installed lirc problems, and have now
gotten as far as lirc successfully connecting to /dev/input/event3 (my DVB
NOVA-S card).

When I start lirc (as below), the first 2 lines appear and the console waits
at "lircd(userspace) ready". Then, when I start IRW on that machine I see
lircd "initializing '/dev/input/event3'. However, lircd seems hung at this
point.

What is going on? I can tell the remote works because the remote arrow keys
are translated to keyboard arrow keys. My lirc version is
0.8.3-73_cvs20071109.fc6. I tried stepping back to version 0.8.2 but lircd
would not recognize the dev/input device.

I've been reading about using a kbd driver as the dev/input for the IR
remote. Without the LIRC part, will MythTV recognize these keyboard events?
How can I find out what events Mythtv responds to? Where to now?

Thanks

====================================================================

[root[at]theatre2 dev]/usr/sbin/lircd -H dev/input -d /dev/input/event3 -n

lircd-0.8.3-CVS[13776]: lircd(userspace) ready

lircd-0.8.3-CVS[13776]: accepted new client on /dev/lircd

lircd-0.8.3-CVS[13776]: initializing '/dev/input/event3'

tino.keitel at gmx

Jan 17, 2008, 8:52 AM

Post #2 of 3 (243 views)
Permalink

Re: lirc incompatible with new dev/input device? [In reply to]

On Thu, Jan 17, 2008 at 11:44:10 -0500, Michelle Dupuis wrote:
> I've been working through some newly installed lirc problems, and have now
> gotten as far as lirc successfully connecting to /dev/input/event3 (my DVB
> NOVA-S card).
>
> When I start lirc (as below), the first 2 lines appear and the console waits
> at "lircd(userspace) ready". Then, when I start IRW on that machine I see
> lircd "initializing '/dev/input/event3'. However, lircd seems hung at this
> point.
>
> What is going on? I can tell the remote works because the remote arrow keys
> are translated to keyboard arrow keys. My lirc version is
> 0.8.3-73_cvs20071109.fc6. I tried stepping back to version 0.8.2 but lircd
> would not recognize the dev/input device.
>
> I've been reading about using a kbd driver as the dev/input for the IR
> remote. Without the LIRC part, will MythTV recognize these keyboard events?
> How can I find out what events Mythtv responds to? Where to now?

You can use the remote without lirc, as the remote acts as an input
device. AFAIK the keys can be mapped with input-kbd from the
input-utils package. However, your MythTV needs to have the keyboard
focus in this case. When you use lirc, the remote works independent of
the keyboard focus.

How exactly do you use lircd? Normally, the remote keys shouldn't
generate keyboard events anymode when lirc uses the device. At least
this is the case in my setup.

Regards,
Tino
_______________________________________________
mythtv-users mailing list
mythtv-users[at]mythtv.org
http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users

support at ocg

Jan 17, 2008, 9:39 AM

Post #3 of 3 (229 views)
Permalink

Re: lirc incompatible with new dev/input device? [In reply to]

If i could get lircd to run, then I could tell you :)
I start lircd with the parameter to use dev/inputX as the device, and then
it listens to that device instead of "default".

Although this should work according to everyting I've read, my just hangs
there at initializing

> -----Original Message-----
> From: mythtv-users-bounces[at]mythtv.org
> [mailto:mythtv-users-bounces[at]mythtv.org] On Behalf Of Tino Keitel
> Sent: Thursday, January 17, 2008 11:52 AM
> To: Myth TV Users List
> Subject: Re: [mythtv-users] lirc incompatible with new
> dev/input device?
>
> On Thu, Jan 17, 2008 at 11:44:10 -0500, Michelle Dupuis wrote:
> > I've been working through some newly installed lirc
> problems, and have
> > now gotten as far as lirc successfully connecting to
> /dev/input/event3
> > (my DVB NOVA-S card).
> >
> > When I start lirc (as below), the first 2 lines appear and
> the console
> > waits at "lircd(userspace) ready". Then, when I start IRW on that
> > machine I see lircd "initializing '/dev/input/event3'.
> However, lircd
> > seems hung at this point.
> >
> > What is going on? I can tell the remote works because the
> remote arrow
> > keys are translated to keyboard arrow keys. My lirc version is
> > 0.8.3-73_cvs20071109.fc6. I tried stepping back to version
> 0.8.2 but
> > lircd would not recognize the dev/input device.
> >
> > I've been reading about using a kbd driver as the dev/input
> for the IR
> > remote. Without the LIRC part, will MythTV recognize these
> keyboard events?
> > How can I find out what events Mythtv responds to? Where to now?
>
> You can use the remote without lirc, as the remote acts as an
> input device. AFAIK the keys can be mapped with input-kbd
> from the input-utils package. However, your MythTV needs to
> have the keyboard focus in this case. When you use lirc, the
> remote works independent of the keyboard focus.
>
> How exactly do you use lircd? Normally, the remote keys
> shouldn't generate keyboard events anymode when lirc uses the
> device. At least this is the case in my setup.
>
> Regards,
> Tino
> _______________________________________________
> mythtv-users mailing list
> mythtv-users[at]mythtv.org
> http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users

_______________________________________________
mythtv-users mailing list
mythtv-users[at]mythtv.org
http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users

Index | Next | Previous | View Threaded

Interested in having your list archived? Contact lists@gossamer-threads.com