Login | Register For Free | Help
Search for: (Advanced)

Mailing List Archive: Linux: Kernel

IDE support on Intel DG965SS

 

 

Linux kernel RSS feed   Index | Next | Previous | View Threaded


alan at chandlerfamily

Dec 10, 2006, 7:58 AM

Post #1 of 6 (3961 views)
Permalink
IDE support on Intel DG965SS

I have been trying to find out if the kernel supports the IDE channel
(with a DVD/CD-R unit attached) on my Intel DG965SS motherboard.

Searching the web indicates that for some motherboards based in the
Intel 965 chipset success has been had for 2.6.18 onward by using the
kernel boot parameters

all-generic-ide pci=nommconf

Although these were Fedora Core 6.

I normally run Debian Unstable - but I have built 2.6.19 and installed
that (using the Debian .config as the base config) - mainly because to
get graphics to work it needs 2.6.19 to recognise the ids for the
agpgart module.

However, despite every thing else working - I can't get the IDE
controller to be recognised - whether or not I use the above kernel
boot parameters. I have been UNABLE to find what all-generic-ide does -
it doesn't seem to be documented anywhere, so I was just blindly
following someones instructions..

lspci -v shows the following

02:00.0 IDE interface: Marvell Technology Group Ltd. Unknown device 6101
(rev b1) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Marvell Technology Group Ltd. Unknown device 6101
Flags: bus master, fast devsel, latency 0, IRQ 10
I/O ports at 1018 [size=8]
I/O ports at 1024 [size=4]
I/O ports at 1010 [size=8]
I/O ports at 1020 [size=4]
I/O ports at 1000 [size=16]
Memory at 50100000 (32-bit, non-prefetchable) [size=512]
Capabilities: [48] Power Management version 2
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit-
Queue=0/0 Enable-
Capabilities: [e0] Express Legacy Endpoint IRQ 0


Poking about in

/sys/devices/pci0000:00/0000:00:02.0

Reveals a vendor and subsystem vendor ID of 0x8086 - which is Intel, and
a subsystem_device of 0x514d.

I had a look in include/linux/pci_ids.h but all I could find there was

#define PCI_DEVICE_ID_ATI_RADEON_QM 0x514d

which doesn't appear related.

Can anyone help me, as to where I can go from here?


--
Alan Chandler
http://www.chandlerfamily.org.uk
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo [at] vger
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/


avi at argo

Dec 10, 2006, 8:30 AM

Post #2 of 6 (3884 views)
Permalink
Re: IDE support on Intel DG965SS [In reply to]

Alan Chandler wrote:
> I have been trying to find out if the kernel supports the IDE channel
> (with a DVD/CD-R unit attached) on my Intel DG965SS motherboard.
>
> Searching the web indicates that for some motherboards based in the
> Intel 965 chipset success has been had for 2.6.18 onward by using the
> kernel boot parameters
>
> all-generic-ide pci=nommconf
>
> Although these were Fedora Core 6.
>
> I normally run Debian Unstable - but I have built 2.6.19 and installed
> that (using the Debian .config as the base config) - mainly because to
> get graphics to work it needs 2.6.19 to recognise the ids for the
> agpgart module.
>
> However, despite every thing else working - I can't get the IDE
> controller to be recognised - whether or not I use the above kernel
> boot parameters. I have been UNABLE to find what all-generic-ide does -
> it doesn't seem to be documented anywhere, so I was just blindly
> following someones instructions..
>
> lspci -v shows the following
>
> 02:00.0 IDE interface: Marvell Technology Group Ltd. Unknown device 6101
> (rev b1) (prog-if 8f [Master SecP SecO PriP PriO])
>

I have the same board at home. I use all-generic-ide (without pci=...)

Do you have CONFIG_IDE_GENERIC set?


--
error compiling committee.c: too many arguments to function

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo [at] vger
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/


alan at lxorguk

Dec 10, 2006, 9:08 AM

Post #3 of 6 (3887 views)
Permalink
Re: IDE support on Intel DG965SS [In reply to]

On Sun, 10 Dec 2006 15:58:33 +0000
Alan Chandler <alan [at] chandlerfamily> wrote:

> I have been trying to find out if the kernel supports the IDE channel
> (with a DVD/CD-R unit attached) on my Intel DG965SS motherboard.

2.6.19-mm and thus hopefully 2.6.20 will support the Marvell via libata
driver pata_marvell.

Alan
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo [at] vger
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/


alan at chandlerfamily

Dec 10, 2006, 11:34 AM

Post #4 of 6 (3877 views)
Permalink
Re: IDE support on Intel DG965SS [In reply to]

On Sunday 10 December 2006 16:30, Avi Kivity wrote:
> Alan Chandler wrote:
> > I have been trying to find out if the kernel supports the IDE
> > channel (with a DVD/CD-R unit attached) on my Intel DG965SS
>
> I have the same board at home. I use all-generic-ide (without
> pci=...)
>
> Do you have CONFIG_IDE_GENERIC set?

It was a module, so presumably that was stopping the parameter working
(or maybe should have loaded it in my initrd). Anyway, recompiled
with it as built in, and with the kernel parameter it seems to work
now. Thanks.

--
Alan Chandler
http://www.chandlerfamily.org.uk
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo [at] vger
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/


shaun at capcentrefoods

Dec 10, 2006, 12:41 PM

Post #5 of 6 (3870 views)
Permalink
Re: IDE support on Intel DG965SS [In reply to]

I have the same board and had the same problems. It now seems to work for
install from the 10.2 RC1 DVD (and I'd assume 10.2 Final). the 2.6.19
kernel tree has support also, you have to find it under the new libata
settings though ("Marvell PATA" controller)

Shaun

On Sun, 10 Dec 2006, Alan Chandler wrote:

> I have been trying to find out if the kernel supports the IDE channel
> (with a DVD/CD-R unit attached) on my Intel DG965SS motherboard.
>
> Searching the web indicates that for some motherboards based in the
> Intel 965 chipset success has been had for 2.6.18 onward by using the
> kernel boot parameters
>
> all-generic-ide pci=nommconf
>
> Although these were Fedora Core 6.
>
> I normally run Debian Unstable - but I have built 2.6.19 and installed
> that (using the Debian .config as the base config) - mainly because to
> get graphics to work it needs 2.6.19 to recognise the ids for the
> agpgart module.
>
> However, despite every thing else working - I can't get the IDE
> controller to be recognised - whether or not I use the above kernel
> boot parameters. I have been UNABLE to find what all-generic-ide does -
> it doesn't seem to be documented anywhere, so I was just blindly
> following someones instructions..
>
> lspci -v shows the following
>
> 02:00.0 IDE interface: Marvell Technology Group Ltd. Unknown device 6101
> (rev b1) (prog-if 8f [Master SecP SecO PriP PriO])
> Subsystem: Marvell Technology Group Ltd. Unknown device 6101
> Flags: bus master, fast devsel, latency 0, IRQ 10
> I/O ports at 1018 [size=8]
> I/O ports at 1024 [size=4]
> I/O ports at 1010 [size=8]
> I/O ports at 1020 [size=4]
> I/O ports at 1000 [size=16]
> Memory at 50100000 (32-bit, non-prefetchable) [size=512]
> Capabilities: [48] Power Management version 2
> Capabilities: [50] Message Signalled Interrupts: Mask- 64bit-
> Queue=0/0 Enable-
> Capabilities: [e0] Express Legacy Endpoint IRQ 0
>
>
> Poking about in
>
> /sys/devices/pci0000:00/0000:00:02.0
>
> Reveals a vendor and subsystem vendor ID of 0x8086 - which is Intel, and
> a subsystem_device of 0x514d.
>
> I had a look in include/linux/pci_ids.h but all I could find there was
>
> #define PCI_DEVICE_ID_ATI_RADEON_QM 0x514d
>
> which doesn't appear related.
>
> Can anyone help me, as to where I can go from here?
>
>
> --
> Alan Chandler
> http://www.chandlerfamily.org.uk
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo [at] vger
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
>
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo [at] vger
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/


shaun at capcentrefoods

Dec 10, 2006, 12:42 PM

Post #6 of 6 (3863 views)
Permalink
Re: IDE support on Intel DG965SS [In reply to]

On Sun, 10 Dec 2006, Alan Chandler wrote:

> I have been trying to find out if the kernel supports the IDE channel
> (with a DVD/CD-R unit attached) on my Intel DG965SS motherboard.
>
> Searching the web indicates that for some motherboards based in the
> Intel 965 chipset success has been had for 2.6.18 onward by using the
> kernel boot parameters
>
> all-generic-ide pci=nommconf
>
> Although these were Fedora Core 6.
>
> I normally run Debian Unstable - but I have built 2.6.19 and installed
> that (using the Debian .config as the base config) - mainly because to
> get graphics to work it needs 2.6.19 to recognise the ids for the
> agpgart module.
>
> However, despite every thing else working - I can't get the IDE
> controller to be recognised - whether or not I use the above kernel
> boot parameters. I have been UNABLE to find what all-generic-ide does -
> it doesn't seem to be documented anywhere, so I was just blindly
> following someones instructions..
>
> lspci -v shows the following
>
> 02:00.0 IDE interface: Marvell Technology Group Ltd. Unknown device 6101
> (rev b1) (prog-if 8f [Master SecP SecO PriP PriO])
> Subsystem: Marvell Technology Group Ltd. Unknown device 6101
> Flags: bus master, fast devsel, latency 0, IRQ 10
> I/O ports at 1018 [size=8]
> I/O ports at 1024 [size=4]
> I/O ports at 1010 [size=8]
> I/O ports at 1020 [size=4]
> I/O ports at 1000 [size=16]
> Memory at 50100000 (32-bit, non-prefetchable) [size=512]
> Capabilities: [48] Power Management version 2
> Capabilities: [50] Message Signalled Interrupts: Mask- 64bit-
> Queue=0/0 Enable-
> Capabilities: [e0] Express Legacy Endpoint IRQ 0
>
>
> Poking about in
>
> /sys/devices/pci0000:00/0000:00:02.0
>
> Reveals a vendor and subsystem vendor ID of 0x8086 - which is Intel, and
> a subsystem_device of 0x514d.
>
> I had a look in include/linux/pci_ids.h but all I could find there was
>
> #define PCI_DEVICE_ID_ATI_RADEON_QM 0x514d
>
> which doesn't appear related.
>
> Can anyone help me, as to where I can go from here?
>
>
> --
> Alan Chandler
> http://www.chandlerfamily.org.uk
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo [at] vger
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
>
and sorry about the previous top post :)
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo [at] vger
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Linux kernel RSS feed   Index | Next | Previous | View Threaded
 
 


Interested in having your list archived? Contact Gossamer Threads
 
  Web Applications & Managed Hosting Powered by Gossamer Threads Inc.