Login | Register For Free | Help
Search for: (Advanced)

Mailing List Archive: ivtv: users

Problems With additional tuners...

  

 
ivtv users RSS feed   Index | Next | Previous | View Threaded


schneideris.peter at gmail

Feb 11, 2012, 10:02 AM

Post #1 of 14 (1087 views)
Permalink
Problems With additional tuners...
Hi All,

I am hoping someone can help me with some trouble shooting that I am doing. I have a box with three Hauppauge cards installed (PVR-500, HVR-2250, and the latest is a HVR 1600). Though I have the 2250 installed I have not built my antenna as of yet to bring it online. My PVR-500 used to work with both tuners but then a couple years ago the second unit just stopped working (no idea why and assumed over time, after lots of attempts to try and revive, that it was just dead). I happened across the HVR-1600 yesterday and thought it would make a good addition for the second Analog tuner that I lost. The problem is that it is providing the same static feed as the second tuner from the PVR-500. After looking at the logs I am starting to wonder if the problemI have is a firmware bug or something else and could use some help. The reason I am turning to this list is because of a line in the syslog in what appears to be the ivtv sequence.

Note: The Analog tuners are being used to capture video through the s-video cable from my satellite tuners and the digital ones are for future OTA HD.

Here is what I see on the two problematic analog tuners.


Here is some background information:

01:06.0 Multimedia video controller: Conexant Systems, Inc. CX23418 Single-Chip MPEG-2 Encoder with Integrated Analog Video/Broadcast Audio Decoder
Subsystem: Hauppauge computer works Inc. WinTV HVR-1600
Flags: bus master, medium devsel, latency 64, IRQ 16
Memory at f8000000 (32-bit, non-prefetchable) [size=64M]
Capabilities: <access denied>
Kernel driver in use: cx18
Kernel modules: cx18

02:08.0 Multimedia video controller: Internext Compression Inc iTVC16 (CX23416) MPEG-2 Encoder (rev 01)
Subsystem: Hauppauge computer works Inc. WinTV PVR 500 (1st unit)
Flags: bus master, medium devsel, latency 64, IRQ 17
Memory at d0000000 (32-bit, prefetchable) [size=64M]
Capabilities: <access denied>
Kernel driver in use: ivtv
Kernel modules: ivtv

02:09.0 Multimedia video controller: Internext Compression Inc iTVC16 (CX23416) MPEG-2 Encoder (rev 01)
Subsystem: Hauppauge computer works Inc. WinTV PVR 500 (2nd unit)
Flags: bus master, medium devsel, latency 64, IRQ 19
Memory at cc000000 (32-bit, prefetchable) [size=64M]
Capabilities: <access denied>
Kernel driver in use: ivtv
Kernel modules: ivtv

05:00.0 Multimedia controller: Philips Semiconductors SAA7164 (rev 81)
Subsystem: Hauppauge computer works Inc. WinTV HVR-2250
Flags: bus master, fast devsel, latency 0, IRQ 18
Memory at fe800000 (64-bit, non-prefetchable) [size=4M]
Memory at fdc00000 (64-bit, non-prefetchable) [size=4M]
Capabilities: <access denied>
Kernel driver in use: saa7164
Kernel modules: saa7164

and:

cat /var/log/syslog|grep cx18
Feb 11 09:22:21 mythtv-primary kernel: [ 12.465299] cx18: Start initialization, version 1.5.0
Feb 11 09:22:21 mythtv-primary kernel: [ 12.516868] cx18-0: Initializing card 0
Feb 11 09:22:21 mythtv-primary kernel: [ 12.516871] cx18-0: Autodetected Hauppauge card
Feb 11 09:22:21 mythtv-primary kernel: [ 12.517062] cx18 0000:01:06.0: PCI INT A -> Link[LNKA] -> GSI 16 (level, low) -> IRQ 16
Feb 11 09:22:21 mythtv-primary kernel: [ 12.523272] cx18-0: cx23418 revision 01010000 (B)
Feb 11 09:22:21 mythtv-primary kernel: [ 12.740991] cx18-0: Autodetected Hauppauge HVR-1600
Feb 11 09:22:21 mythtv-primary kernel: [ 12.740993] cx18-0: Simultaneous Digital and Analog TV capture supported
Feb 11 09:22:21 mythtv-primary kernel: [ 12.982069] cs5345 3-004c: chip found @ 0x98 (cx18 i2c driver #0-0)
Feb 11 09:22:21 mythtv-primary kernel: [ 13.000831] cx18-0: Registered device video2 for encoder MPEG (64 x 32.00 kB)
Feb 11 09:22:21 mythtv-primary kernel: [ 13.000839] DVB: registering new adapter (cx18)
Feb 11 09:22:21 mythtv-primary kernel: [ 13.883461] cx18-0: DVB Frontend registered
Feb 11 09:22:21 mythtv-primary kernel: [ 13.883464] cx18-0: Registered DVB adapter0 for TS (32 x 32.00 kB)
Feb 11 09:22:21 mythtv-primary kernel: [ 13.883501] cx18-0: Registered device video34 for encoder YUV (20 x 101.25 kB)
Feb 11 09:22:21 mythtv-primary kernel: [ 13.883540] cx18-0: Registered device vbi2 for encoder VBI (20 x 51984 bytes)
Feb 11 09:22:21 mythtv-primary kernel: [ 13.883567] cx18-0: Registered device video26 for encoder PCM audio (256 x 4.00 kB)
Feb 11 09:22:21 mythtv-primary kernel: [ 13.883570] cx18-0: Initialized card: Hauppauge HVR-1600
Feb 11 09:22:21 mythtv-primary kernel: [ 13.883631] cx18: End initialization
Feb 11 09:22:21 mythtv-primary kernel: [ 13.995615] cx18-alsa: module loading...
Feb 11 09:22:21 mythtv-primary kernel: [ 14.162692] cx18-0: loaded v4l-cx23418-cpu.fw firmware (158332 bytes)
Feb 11 09:22:21 mythtv-primary kernel: [ 14.413193] cx18-0: loaded v4l-cx23418-apu.fw firmware V00120000 (141200 bytes)
Feb 11 09:22:21 mythtv-primary kernel: [ 14.472491] cx18-0: FW version: 0.0.74.0 (Release 2007/03/12)
Feb 11 09:22:21 mythtv-primary kernel: [ 15.738362] cx18-0 843: loaded v4l-cx23418-dig.fw firmware (16382 bytes)
Feb 11 09:22:21 mythtv-primary kernel: [ 15.760120] cx18-0 843: verified load of v4l-cx23418-dig.fw firmware (16382 bytes)

and what set my into this e-mail:



Feb 11 09:22:21 mythtv-primary kernel: [ 12.371758] Linux video capture interface: v2.00
Feb 11 09:22:21 mythtv-primary kernel: [ 12.382727] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Feb 11 09:22:21 mythtv-primary kernel: [ 12.449074] ivtv: Start initialization, version 1.4.2
Feb 11 09:22:21 mythtv-primary kernel: [ 12.453711] parport_pc 00:05: reported by Plug and Play ACPI
Feb 11 09:22:21 mythtv-primary kernel: [ 12.453762] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
Feb 11 09:22:21 mythtv-primary kernel: [ 12.456724] [Firmware Bug]: ACPI(IGPU) defines _DOD but not _DOS
Feb 11 09:22:21 mythtv-primary kernel: [ 12.457016] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:12/LNXVIDEO:00/input/input5
Feb 11 09:22:21 mythtv-primary kernel: [ 12.457108] ACPI: Video Device [IGPU] (multi-head: yes rom: no post: no)
Feb 11 09:22:21 mythtv-primary kernel: [ 12.458546] ivtv0: Initializing card 0
Feb 11 09:22:21 mythtv-primary kernel: [ 12.458552] ivtv0: Autodetected Hauppauge card (cx23416 based)
Feb 11 09:22:21 mythtv-primary kernel: [ 12.461226] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 17
Feb 11 09:22:21 mythtv-primary kernel: [ 12.461251] ivtv 0000:02:08.0: PCI INT A -> Link[LNKB] -> GSI 17 (level, low) -> IRQ 17
Feb 11 09:22:21 mythtv-primary kernel: [ 12.465299] cx18: Start initialization, version 1.5.0
Feb 11 09:22:21 mythtv-primary kernel: [ 12.516569] tveeprom 2-0050: Hauppauge model 23552, rev E792, serial# 10603908
Feb 11 09:22:21 mythtv-primary kernel: [ 12.516572] tveeprom 2-0050: tuner model is Philips FQ1236A MK4 (idx 92, type 57)
Feb 11 09:22:21 mythtv-primary kernel: [ 12.516575] tveeprom 2-0050: TV standards NTSC(M) (eeprom 0x08)
Feb 11 09:22:21 mythtv-primary kernel: [ 12.516577] tveeprom 2-0050: second tuner model is Philips TEA5768HL FM Radio (idx 101, type 62)
Feb 11 09:22:21 mythtv-primary kernel: [ 12.516580] tveeprom 2-0050: audio processor is CX25843 (idx 37)
Feb 11 09:22:21 mythtv-primary kernel: [ 12.516582] tveeprom 2-0050: decoder processor is CX25843 (idx 30)
Feb 11 09:22:21 mythtv-primary kernel: [ 12.516584] tveeprom 2-0050: has radio
Feb 11 09:22:21 mythtv-primary kernel: [ 12.516586] ivtv0: Autodetected WinTV PVR 500 (unit #1)
Feb 11 09:22:21 mythtv-primary kernel: [ 12.516630] HDA Intel 0000:00:07.0: power state changed by ACPI to D0
Feb 11 09:22:21 mythtv-primary kernel: [ 12.516635] HDA Intel 0000:00:07.0: power state changed by ACPI to D0
Feb 11 09:22:21 mythtv-primary kernel: [ 12.516789] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 21
Feb 11 09:22:21 mythtv-primary kernel: [ 12.516793] HDA Intel 0000:00:07.0: PCI INT A -> Link[LAZA] -> GSI 21 (level, low) -> IRQ 21
Feb 11 09:22:21 mythtv-primary kernel: [ 12.516795] hda_intel: Disabling MSI
Feb 11 09:22:21 mythtv-primary kernel: [ 12.516818] HDA Intel 0000:00:07.0: setting latency timer to 64
Feb 11 09:22:21 mythtv-primary kernel: [ 12.516868] cx18-0: Initializing card 0
Feb 11 09:22:21 mythtv-primary kernel: [ 12.516871] cx18-0: Autodetected Hauppauge card
Feb 11 09:22:21 mythtv-primary kernel: [ 12.517047] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 16
Feb 11 09:22:21 mythtv-primary kernel: [ 12.517062] cx18 0000:01:06.0: PCI INT A -> Link[LNKA] -> GSI 16 (level, low) -> IRQ 16
Feb 11 09:22:21 mythtv-primary kernel: [ 12.523272] cx18-0: cx23418 revision 01010000 (B)
Feb 11 09:22:21 mythtv-primary kernel: [ 12.527518] cx25840 2-0044: cx25843-24 found @ 0x88 (ivtv i2c driver #0)
Feb 11 09:22:21 mythtv-primary kernel: [ 12.552242] lp0: using parport0 (interrupt-driven).
Feb 11 09:22:21 mythtv-primary kernel: [ 12.559592] i2c-core: driver [tuner] using legacy suspend method
Feb 11 09:22:21 mythtv-primary kernel: [ 12.559595] i2c-core: driver [tuner] using legacy resume method
Feb 11 09:22:21 mythtv-primary kernel: [ 12.571404] tea5767 2-0060: type set to Philips TEA5767HN FM Radio
Feb 11 09:22:21 mythtv-primary kernel: [ 12.572716] tuner 2-0060: Tuner 62 found with type(s) Radio.
Feb 11 09:22:21 mythtv-primary kernel: [ 12.647194] tda9887 2-0043: creating new instance
Feb 11 09:22:21 mythtv-primary kernel: [ 12.647198] tda9887 2-0043: tda988[5/6/7] found
Feb 11 09:22:21 mythtv-primary kernel: [ 12.648262] tuner 2-0043: Tuner 74 found with type(s) Radio TV.
Feb 11 09:22:21 mythtv-primary kernel: [ 12.649550] EXT4-fs (sdc1): re-mounted. Opts: errors=remount-ro
Feb 11 09:22:21 mythtv-primary kernel: [ 12.661166] tuner 2-0061: Tuner -1 found with type(s) TV.
Feb 11 09:22:21 mythtv-primary kernel: [ 12.661266] MCE: In-kernel MCE decoding enabled.
Feb 11 09:22:21 mythtv-primary kernel: [ 12.662420] EDAC MC: Ver: 2.1.0
Feb 11 09:22:21 mythtv-primary kernel: [ 12.667708] AMD64 EDAC driver v3.4.0
Feb 11 09:22:21 mythtv-primary kernel: [ 12.669263] wm8775 2-001b: chip found @ 0x36 (ivtv i2c driver #0)
Feb 11 09:22:21 mythtv-primary kernel: [ 12.679969] type=1400 audit(1328977336.392:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=765 comm="apparmor_parser"
Feb 11 09:22:21 mythtv-primary kernel: [ 12.680434] type=1400 audit(1328977336.396:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=765 comm="apparmor_parser"
Feb 11 09:22:21 mythtv-primary kernel: [ 12.680697] type=1400 audit(1328977336.396:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=765 comm="apparmor_parser"
Feb 11 09:22:21 mythtv-primary kernel: [ 12.683264] type=1400 audit(1328977336.396:5): apparmor="STATUS" operation="profile_load" name="/usr/sbin/ntpd" pid=786 comm="apparmor_parser"
Feb 11 09:22:21 mythtv-primary kernel: [ 12.691569] saa7164 driver loaded
Feb 11 09:22:21 mythtv-primary kernel: [ 12.695133] saa7164 0000:05:00.0: PCI INT A -> Link[LN2A] -> GSI 18 (level, low) -> IRQ 18
Feb 11 09:22:21 mythtv-primary kernel: [ 12.695958] CORE saa7164[0]: subsystem: 0070:8851, board: Hauppauge WinTV-HVR2250 [card=7,autodetected]
Feb 11 09:22:21 mythtv-primary kernel: [ 12.695962] saa7164[0]/0: found at 0000:05:00.0, rev: 129, irq: 18, latency: 0, mmio: 0xfe800000
Feb 11 09:22:21 mythtv-primary kernel: [ 12.695968] saa7164 0000:05:00.0: setting latency timer to 64
Feb 11 09:22:21 mythtv-primary kernel: [ 12.698088] tuner-simple 2-0061: creating new instance
Feb 11 09:22:21 mythtv-primary kernel: [ 12.698093] tuner-simple 2-0061: type set to 57 (Philips FQ1236A MK4)
Feb 11 09:22:21 mythtv-primary kernel: [ 12.699764] ivtv0: Registered device video0 for encoder MPG (4096 kB)
Feb 11 09:22:21 mythtv-primary kernel: [ 12.699792] ivtv0: Registered device video32 for encoder YUV (2048 kB)
Feb 11 09:22:21 mythtv-primary kernel: [ 12.699818] ivtv0: Registered device vbi0 for encoder VBI (1024 kB)
Feb 11 09:22:21 mythtv-primary kernel: [ 12.699841] ivtv0: Registered device video24 for encoder PCM (320 kB)
Feb 11 09:22:21 mythtv-primary kernel: [ 12.699866] ivtv0: Registered device radio0 for encoder radio
Feb 11 09:22:21 mythtv-primary kernel: [ 12.699868] ivtv0: Initialized card: WinTV PVR 500 (unit #1)
Feb 11 09:22:21 mythtv-primary kernel: [ 12.740974] tveeprom 3-0050: Hauppauge model 74041, rev C6G8, serial# 7255283
Feb 11 09:22:21 mythtv-primary kernel: [ 12.740977] tveeprom 3-0050: MAC address is 00:0d:fe:6e:b4:f3
Feb 11 09:22:21 mythtv-primary kernel: [ 12.740979] tveeprom 3-0050: tuner model is TCL M30WTP-4N-E (idx 168, type 85)
Feb 11 09:22:21 mythtv-primary kernel: [ 12.740982] tveeprom 3-0050: TV standards NTSC(M) (eeprom 0x08)
Feb 11 09:22:21 mythtv-primary kernel: [ 12.740984] tveeprom 3-0050: audio processor is CX23418 (idx 38)
Feb 11 09:22:21 mythtv-primary kernel: [ 12.740986] tveeprom 3-0050: decoder processor is CX23418 (idx 31)
Feb 11 09:22:21 mythtv-primary kernel: [ 12.740988] tveeprom 3-0050: has no radio, has IR receiver, has IR transmitter
Feb 11 09:22:21 mythtv-primary kernel: [ 12.740991] cx18-0: Autodetected Hauppauge HVR-1600
Feb 11 09:22:21 mythtv-primary kernel: [ 12.740993] cx18-0: Simultaneous Digital and Analog TV capture supported
Feb 11 09:22:21 mythtv-primary kernel: [ 12.748153] ivtv1: Initializing card 1
Feb 11 09:22:21 mythtv-primary kernel: [ 12.748158] ivtv1: Autodetected Hauppauge card (cx23416 based)
Feb 11 09:22:21 mythtv-primary kernel: [ 12.749970] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 19
Feb 11 09:22:21 mythtv-primary kernel: [ 12.749978] ivtv 0000:02:09.0: PCI INT A -> Link[LNKC] -> GSI 19 (level, low) -> IRQ 19
Feb 11 09:22:21 mythtv-primary kernel: [ 12.805055] tveeprom 5-0050: Hauppauge model 23552, rev E792, serial# 10603908
Feb 11 09:22:21 mythtv-primary kernel: [ 12.805058] tveeprom 5-0050: tuner model is Philips FQ1236A MK4 (idx 92, type 57)
Feb 11 09:22:21 mythtv-primary kernel: [ 12.805060] tveeprom 5-0050: TV standards NTSC(M) (eeprom 0x08)
Feb 11 09:22:21 mythtv-primary kernel: [ 12.805063] tveeprom 5-0050: second tuner model is Philips TEA5768HL FM Radio (idx 101, type 62)
Feb 11 09:22:21 mythtv-primary kernel: [ 12.805065] tveeprom 5-0050: audio processor is CX25843 (idx 37)
Feb 11 09:22:21 mythtv-primary kernel: [ 12.805067] tveeprom 5-0050: decoder processor is CX25843 (idx 30)
Feb 11 09:22:21 mythtv-primary kernel: [ 12.805069] tveeprom 5-0050: has radio
Feb 11 09:22:21 mythtv-primary kernel: [ 12.805071] ivtv1: Correcting tveeprom data: no radio present on second unit
Feb 11 09:22:21 mythtv-primary kernel: [ 12.805073] ivtv1: Autodetected WinTV PVR 500 (unit #2)
Feb 11 09:22:21 mythtv-primary kernel: [ 12.811719] cx25840 5-0044: cx25843-24 found @ 0x88 (ivtv i2c driver #1)
Feb 11 09:22:21 mythtv-primary kernel: [ 12.833014] tda9887 5-0043: creating new instance
Feb 11 09:22:21 mythtv-primary kernel: [ 12.833017] tda9887 5-0043: tda988[5/6/7] found
Feb 11 09:22:21 mythtv-primary kernel: [ 12.834052] tuner 5-0043: Tuner 74 found with type(s) Radio TV.
Feb 11 09:22:21 mythtv-primary kernel: [ 12.839893] tuner 5-0061: Tuner -1 found with type(s) Radio TV.
Feb 11 09:22:21 mythtv-primary kernel: [ 12.845534] wm8775 5-001b: chip found @ 0x36 (ivtv i2c driver #1)
Feb 11 09:22:21 mythtv-primary kernel: [ 12.863936] tuner-simple 5-0061: creating new instance
Feb 11 09:22:21 mythtv-primary kernel: [ 12.863940] tuner-simple 5-0061: type set to 57 (Philips FQ1236A MK4)
Feb 11 09:22:21 mythtv-primary kernel: [ 12.865665] ivtv1: Registered device video1 for encoder MPG (4096 kB)
Feb 11 09:22:21 mythtv-primary kernel: [ 12.865692] ivtv1: Registered device video33 for encoder YUV (2048 kB)
Feb 11 09:22:21 mythtv-primary kernel: [ 12.865717] ivtv1: Registered device vbi1 for encoder VBI (1024 kB)
Feb 11 09:22:21 mythtv-primary kernel: [ 12.865743] ivtv1: Registered device video25 for encoder PCM (320 kB)
Feb 11 09:22:21 mythtv-primary kernel: [ 12.865745] ivtv1: Initialized card: WinTV PVR 500 (unit #2)
Feb 11 09:22:21 mythtv-primary kernel: [ 12.865799] ivtv: End initialization
Feb 11 09:22:21 mythtv-primary kernel: [ 12.913467] tda9887 4-0043: creating new instance
Feb 11 09:22:21 mythtv-primary kernel: [ 12.913470] tda9887 4-0043: tda988[5/6/7] found
Feb 11 09:22:21 mythtv-primary kernel: [ 12.914339] tuner 4-0043: Tuner 74 found with type(s) Radio TV.
Feb 11 09:22:21 mythtv-primary kernel: [ 12.920094] tuner 4-0061: Tuner -1 found with type(s) Radio TV.
Feb 11 09:22:21 mythtv-primary kernel: [ 12.944043] saa7164_downloadfirmware() no first image
Feb 11 09:22:21 mythtv-primary kernel: [ 12.944055] saa7164_downloadfirmware() Waiting for firmware upload (NXP7164-2010-03-10.1.fw)
Feb 11 09:22:21 mythtv-primary kernel: [ 12.964660] JFS: nTxBlock = 8192, nTxLock = 65536
Feb 11 09:22:21 mythtv-primary kernel: [ 12.982069] cs5345 3-004c: chip found @ 0x98 (cx18 i2c driver #0-0)
Feb 11 09:22:21 mythtv-primary kernel: [ 12.986133] tuner-simple 4-0061: creating new instance
Feb 11 09:22:21 mythtv-primary kernel: [ 12.986136] tuner-simple 4-0061: type set to 85 (Philips FQ1236 MK5)
Feb 11 09:22:21 mythtv-primary kernel: [ 13.000831] cx18-0: Registered device video2 for encoder MPEG (64 x 32.00 kB)
Feb 11 09:22:21 mythtv-primary kernel: [ 13.000839] DVB: registering new adapter (cx18)
Feb 11 09:22:21 mythtv-primary kernel: [ 13.001366] ppdev: user-space parallel port driver
Feb 11 09:22:21 mythtv-primary kernel: [ 13.093375] saa7164_downloadfirmware() Upload failed. (file not found?)
Feb 11 09:22:21 mythtv-primary kernel: [ 13.093380] Failed to boot firmware, no features registered
Feb 11 09:22:21 mythtv-primary kernel: [ 13.250727] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
Feb 11 09:22:21 mythtv-primary kernel: [ 13.510643] EXT4-fs (sdd1): mounted filesystem with ordered data mode. Opts: (null)
Feb 11 09:22:21 mythtv-primary kernel: [ 13.673594] ivtv0: Loaded v4l-cx2341x-enc.fw firmware (376836 bytes)
Feb 11 09:22:21 mythtv-primary kernel: [ 13.701587] ivtv1: Loaded v4l-cx2341x-enc.fw firmware (376836 bytes)
Feb 11 09:22:21 mythtv-primary kernel: [ 13.772527] k8temp 0000:00:18.3: Temperature readouts might be wrong - check erratum #141
Feb 11 09:22:21 mythtv-primary kernel: [ 13.772807] EDAC amd64: DRAM ECC disabled.
Feb 11 09:22:21 mythtv-primary kernel: [ 13.772813] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
Feb 11 09:22:21 mythtv-primary kernel: [ 13.772814] Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
Feb 11 09:22:21 mythtv-primary kernel: [ 13.772815] (Note that use of the override may cause unknown side effects.)
Feb 11 09:22:21 mythtv-primary kernel: [ 13.872180] ivtv0: Encoder revision: 0x02060039
Feb 11 09:22:21 mythtv-primary kernel: [ 13.883339] MXL5005S: Attached at address 0x63
Feb 11 09:22:21 mythtv-primary kernel: [ 13.883344] DVB: registering adapter 0 frontend 0 (Samsung S5H1409 QAM/8VSB Frontend)...
Feb 11 09:22:21 mythtv-primary kernel: [ 13.883461] cx18-0: DVB Frontend registered
Feb 11 09:22:21 mythtv-primary kernel: [ 13.883464] cx18-0: Registered DVB adapter0 for TS (32 x 32.00 kB)
Feb 11 09:22:21 mythtv-primary kernel: [ 13.883501] cx18-0: Registered device video34 for encoder YUV (20 x 101.25 kB)
Feb 11 09:22:21 mythtv-primary kernel: [ 13.883540] cx18-0: Registered device vbi2 for encoder VBI (20 x 51984 bytes)
Feb 11 09:22:21 mythtv-primary kernel: [ 13.883567] cx18-0: Registered device video26 for encoder PCM audio (256 x 4.00 kB)
Feb 11 09:22:21 mythtv-primary kernel: [ 13.883570] cx18-0: Initialized card: Hauppauge HVR-1600
Feb 11 09:22:21 mythtv-primary kernel: [ 13.883631] cx18: End initialization
Feb 11 09:22:21 mythtv-primary kernel: [ 13.900395] ivtv1: Encoder revision: 0x02060039
Feb 11 09:22:21 mythtv-primary kernel: [ 13.995615] cx18-alsa: module loading...
Feb 11 09:22:21 mythtv-primary kernel: [ 14.162692] cx18-0: loaded v4l-cx23418-cpu.fw firmware (158332 bytes)
Feb 11 09:22:21 mythtv-primary kernel: [ 14.413193] cx18-0: loaded v4l-cx23418-apu.fw firmware V00120000 (141200 bytes)
Feb 11 09:22:21 mythtv-primary kernel: [ 14.472491] cx18-0: FW version: 0.0.74.0 (Release 2007/03/12)
Feb 11 09:22:21 mythtv-primary kernel: [ 15.305943] nvidia: module license 'NVIDIA' taints kernel.
Feb 11 09:22:21 mythtv-primary kernel: [ 15.305948] Disabling lock debugging due to kernel taint
Feb 11 09:22:21 mythtv-primary kernel: [ 15.543106] ACPI: PCI Interrupt Link [SGRU] enabled at IRQ 20
Feb 11 09:22:21 mythtv-primary kernel: [ 15.543114] nvidia 0000:03:00.0: PCI INT A -> Link[SGRU] -> GSI 20 (level, low) -> IRQ 20
Feb 11 09:22:21 mythtv-primary kernel: [ 15.543122] nvidia 0000:03:00.0: setting latency timer to 64
Feb 11 09:22:21 mythtv-primary kernel: [ 15.543127] vgaarb: device changed decodes: PCI:0000:03:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
Feb 11 09:22:21 mythtv-primary kernel: [ 15.544170] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 290.10 Wed Nov 16 17:39:29 PST 2011
Feb 11 09:22:21 mythtv-primary kernel: [ 15.738362] cx18-0 843: loaded v4l-cx23418-dig.fw firmware (16382 bytes)
Feb 11 09:22:21 mythtv-primary kernel: [ 15.760120] cx18-0 843: verified load of v4l-cx23418-dig.fw firmware (16382 bytes)
Feb 11 09:22:21 mythtv-primary kernel: [ 17.589877] cx25840 5-0044: loaded v4l-cx25840.fw firmware (16382 bytes)
Feb 11 09:22:21 mythtv-primary kernel: [ 17.899715] RPC: Registered named UNIX socket transport module.

Can anyone tell me if I have an actual firmware bug or if this is normal? Can anyone tell me how to test the card for sure to see if it is a defective card?

-Peter
Attachments: PastedGraphic-1.png (183 KB)


awalls at md

Feb 11, 2012, 2:02 PM

Post #2 of 14 (1045 views)
Permalink
Re: Problems With additional tuners... [In reply to]
On Sat, 2012-02-11 at 11:02 -0700, Gmail wrote:
> Hi All,
>
>
> I am hoping someone can help me with some trouble shooting that I am
> doing. I have a box with three Hauppauge cards installed (PVR-500,
> HVR-2250, and the latest is a HVR 1600). Though I have the 2250
> installed I have not built my antenna as of yet to bring it online.
> My PVR-500 used to work with both tuners but then a couple years ago
> the second unit just stopped working (no idea why and assumed over
> time, after lots of attempts to try and revive, that it was just
> dead). I happened across the HVR-1600 yesterday and thought it would
> make a good addition for the second Analog tuner that I lost. The
> problem is that it is providing the same static feed as the second
> tuner from the PVR-500. After looking at the logs I am starting to
> wonder if the problemI have is a firmware bug or something else and
> could use some help. The reason I am turning to this list is because
> of a line in the syslog in what appears to be the ivtv sequence.
>
>
> Note: The Analog tuners are being used to capture video through the
> s-video cable from my satellite tuners and the digital ones are for
> future OTA HD.

Please install v4l2-ctl (probably in a v4l2-utils package) and mplayer.

Kill the mythbackend, if it is running.

Then run v4l2-ctl --list-devices, to see what card corresponds to which
devices nodes. For example:

$ v4l2-ctl --list-devices
Hauppauge HVR-1600 (PCI:0000:03:00.0):
/dev/video0
/dev/video24
/dev/video32
/dev/vbi0

Hauppauge WinTV PVR-150 (PCI:0000:03:01.0):
/dev/video2
/dev/video26
/dev/video34
/dev/radio2
/dev/vbi2

Hauppauge HVR-1600 (PCI:0000:03:02.0):
/dev/video1
/dev/video25
/dev/video33
/dev/radio1
/dev/vbi1

On a device from which you wish to capture S-Video, set the proper input
and analog TV standard using v4l2-ctl:

$ v4l2-ctl -d /dev/video0 --list-inputs
ioctl: VIDIOC_ENUMINPUT
Input : 0
Name : Tuner 1
Type : 0x00000001
Audioset : 0x00000007
Tuner : 0x00000000
Standard : 0x0000000000001000 (NTSC-M)
Status : 0x00000000 (ok)
Capabilities: 0x00000004 (SD presets)

Input : 1
Name : S-Video 1
Type : 0x00000002
Audioset : 0x00000007
Tuner : 0x00000000
Standard : 0x0000000000FFFFFF (PAL-B/B1/G/H/I/D/D1/K/M/N/Nc/60 NTSC-M/M-JP/443/M-KR SECAM-B/D/G/H/K/K1/L/Lc)
Status : 0x00000000 (ok)
Capabilities: 0x00000004 (SD presets)

Input : 2
Name : Composite 1
Type : 0x00000002
Audioset : 0x00000007
Tuner : 0x00000000
Standard : 0x0000000000FFFFFF (PAL-B/B1/G/H/I/D/D1/K/M/N/Nc/60 NTSC-M/M-JP/443/M-KR SECAM-B/D/G/H/K/K1/L/Lc)
Status : 0x00000000 (ok)
Capabilities: 0x00000004 (SD presets)
[...]

$ v4l2-ctl -d /dev/video0 --set-input=1
Video input set to 1 (S-Video 1: ok)

$ v4l2-ctl -d /dev/video0 --list-standards
ioctl: VIDIOC_ENUMSTD
Index : 0
ID : 0x000000000000B000
Name : NTSC
Frame period: 1001/30000
Frame lines : 525

Index : 1
ID : 0x0000000000001000
Name : NTSC-M
Frame period: 1001/30000
Frame lines : 525
[...]

$ v4l2-ctl -d /dev/video0 --set-standard=1
Standard set to 00001000


Turn on your S-Video source, and then just capture an MPEG live with mplayer:

$ mplayer /dev/video0 -cache 8192

or capture a file for later playback

$ cat /dev/video0 > foo.mpg
^C
$ mplayer foo.mpg



> Here is what I see on the two problematic analog tuners.

Looks like an untuned tuner input driving the encoder, not S-Video. An
S-Video input that is connected but has no signal is usually a solid
grey or black screen.

>
> Here is some background information:

> and:
>
>
> cat /var/log/syslog|grep cx18
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.465299] cx18: Start initialization, version 1.5.0
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516868] cx18-0: Initializing card 0
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516871] cx18-0: Autodetected Hauppauge card
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.517062] cx18 0000:01:06.0: PCI INT A -> Link[LNKA] -> GSI 16 (level, low) -> IRQ 16
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.523272] cx18-0: cx23418 revision 01010000 (B)
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.740991] cx18-0: Autodetected Hauppauge HVR-1600

greping for 'cx18' will miss any error messages reltaed to the tuner
chips and initialization. Anyway, the HVR-1600 lloks OK from what you
provided.

>
> and what set my into this e-mail:
>
>
>
>
>
>
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.371758] Linux video capture interface: v2.00
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.382727] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.449074] ivtv: Start initialization, version 1.4.2
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.453711] parport_pc 00:05: reported by Plug and Play ACPI
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.453762] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.456724] [Firmware Bug]: ACPI(IGPU) defines _DOD but not _DOS

Your computer's BIOS has an ACPI bug that is unrelated to the video
capture cards, AFAICT.


> Feb 11 09:22:21 mythtv-primary kernel: [ 12.457016] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:12/LNXVIDEO:00/input/input5
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.457108] ACPI: Video Device [IGPU] (multi-head: yes rom: no post: no)
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.458546] ivtv0: Initializing card 0
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.458552] ivtv0: Autodetected Hauppauge card (cx23416 based)
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.461226] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 17
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.461251] ivtv 0000:02:08.0: PCI INT A -> Link[LNKB] -> GSI 17 (level, low) -> IRQ 17
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.465299] cx18: Start initialization, version 1.5.0
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516569] tveeprom 2-0050: Hauppauge model 23552, rev E792, serial# 10603908
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516572] tveeprom 2-0050: tuner model is Philips FQ1236A MK4 (idx 92, type 57)
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516575] tveeprom 2-0050: TV standards NTSC(M) (eeprom 0x08)
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516577] tveeprom 2-0050: second tuner model is Philips TEA5768HL FM Radio (idx 101, type 62)
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516580] tveeprom 2-0050: audio processor is CX25843 (idx 37)
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516582] tveeprom 2-0050: decoder processor is CX25843 (idx 30)
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516584] tveeprom 2-0050: has radio
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516586] ivtv0: Autodetected WinTV PVR 500 (unit #1)
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516630] HDA Intel 0000:00:07.0: power state changed by ACPI to D0
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516635] HDA Intel 0000:00:07.0: power state changed by ACPI to D0
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516789] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 21
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516793] HDA Intel 0000:00:07.0: PCI INT A -> Link[LAZA] -> GSI 21 (level, low) -> IRQ 21
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516795] hda_intel: Disabling MSI
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516818] HDA Intel 0000:00:07.0: setting latency timer to 64
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516868] cx18-0: Initializing card 0
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516871] cx18-0: Autodetected Hauppauge card
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.517047] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 16
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.517062] cx18 0000:01:06.0: PCI INT A -> Link[LNKA] -> GSI 16 (level, low) -> IRQ 16
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.523272] cx18-0: cx23418 revision 01010000 (B)
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.527518] cx25840 2-0044: cx25843-24 found @ 0x88 (ivtv i2c driver #0)
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.552242] lp0: using parport0 (interrupt-driven).
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.559592] i2c-core: driver [tuner] using legacy suspend method
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.559595] i2c-core: driver [tuner] using legacy resume method
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.571404] tea5767 2-0060: type set to Philips TEA5767HN FM Radio
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.572716] tuner 2-0060: Tuner 62 found with type(s) Radio.
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.647194] tda9887 2-0043: creating new instance
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.647198] tda9887 2-0043: tda988[5/6/7] found
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.648262] tuner 2-0043: Tuner 74 found with type(s) Radio TV.
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.649550] EXT4-fs (sdc1): re-mounted. Opts: errors=remount-ro
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.661166] tuner 2-0061: Tuner -1 found with type(s) TV.
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.661266] MCE: In-kernel MCE decoding enabled.
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.662420] EDAC MC: Ver: 2.1.0
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.667708] AMD64 EDAC driver v3.4.0
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.669263] wm8775 2-001b: chip found @ 0x36 (ivtv i2c driver #0)
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.679969] type=1400 audit(1328977336.392:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=765 comm="apparmor_parser"
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.680434] type=1400 audit(1328977336.396:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=765 comm="apparmor_parser"
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.680697] type=1400 audit(1328977336.396:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=765 comm="apparmor_parser"
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.683264] type=1400 audit(1328977336.396:5): apparmor="STATUS" operation="profile_load" name="/usr/sbin/ntpd" pid=786 comm="apparmor_parser"
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.691569] saa7164 driver loaded
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.695133] saa7164 0000:05:00.0: PCI INT A -> Link[LN2A] -> GSI 18 (level, low) -> IRQ 18
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.695958] CORE saa7164[0]: subsystem: 0070:8851, board: Hauppauge WinTV-HVR2250 [card=7,autodetected]
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.695962] saa7164[0]/0: found at 0000:05:00.0, rev: 129, irq: 18, latency: 0, mmio: 0xfe800000
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.695968] saa7164 0000:05:00.0: setting latency timer to 64
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.698088] tuner-simple 2-0061: creating new instance
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.698093] tuner-simple 2-0061: type set to 57 (Philips FQ1236A MK4)
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.699764] ivtv0: Registered device video0 for encoder MPG (4096 kB)
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.699792] ivtv0: Registered device video32 for encoder YUV (2048 kB)
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.699818] ivtv0: Registered device vbi0 for encoder VBI (1024 kB)
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.699841] ivtv0: Registered device video24 for encoder PCM (320 kB)
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.699866] ivtv0: Registered device radio0 for encoder radio
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.699868] ivtv0: Initialized card: WinTV PVR 500 (unit #1)
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.740974] tveeprom 3-0050: Hauppauge model 74041, rev C6G8, serial# 7255283
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.740977] tveeprom 3-0050: MAC address is 00:0d:fe:6e:b4:f3
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.740979] tveeprom 3-0050: tuner model is TCL M30WTP-4N-E (idx 168, type 85)
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.740982] tveeprom 3-0050: TV standards NTSC(M) (eeprom 0x08)
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.740984] tveeprom 3-0050: audio processor is CX23418 (idx 38)
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.740986] tveeprom 3-0050: decoder processor is CX23418 (idx 31)
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.740988] tveeprom 3-0050: has no radio, has IR receiver, has IR transmitter
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.740991] cx18-0: Autodetected Hauppauge HVR-1600
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.740993] cx18-0: Simultaneous Digital and Analog TV capture supported
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.748153] ivtv1: Initializing card 1
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.748158] ivtv1: Autodetected Hauppauge card (cx23416 based)
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.749970] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 19
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.749978] ivtv 0000:02:09.0: PCI INT A -> Link[LNKC] -> GSI 19 (level, low) -> IRQ 19
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.805055] tveeprom 5-0050: Hauppauge model 23552, rev E792, serial# 10603908
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.805058] tveeprom 5-0050: tuner model is Philips FQ1236A MK4 (idx 92, type 57)
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.805060] tveeprom 5-0050: TV standards NTSC(M) (eeprom 0x08)
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.805063] tveeprom 5-0050: second tuner model is Philips TEA5768HL FM Radio (idx 101, type 62)
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.805065] tveeprom 5-0050: audio processor is CX25843 (idx 37)
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.805067] tveeprom 5-0050: decoder processor is CX25843 (idx 30)
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.805069] tveeprom 5-0050: has radio
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.805071] ivtv1: Correcting tveeprom data: no radio present on second unit
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.805073] ivtv1: Autodetected WinTV PVR 500 (unit #2)
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.811719] cx25840 5-0044: cx25843-24 found @ 0x88 (ivtv i2c driver #1)
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.833014] tda9887 5-0043: creating new instance
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.833017] tda9887 5-0043: tda988[5/6/7] found
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.834052] tuner 5-0043: Tuner 74 found with type(s) Radio TV.
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.839893] tuner 5-0061: Tuner -1 found with type(s) Radio TV.
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.845534] wm8775 5-001b: chip found @ 0x36 (ivtv i2c driver #1)
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.863936] tuner-simple 5-0061: creating new instance
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.863940] tuner-simple 5-0061: type set to 57 (Philips FQ1236A MK4)
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.865665] ivtv1: Registered device video1 for encoder MPG (4096 kB)
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.865692] ivtv1: Registered device video33 for encoder YUV (2048 kB)
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.865717] ivtv1: Registered device vbi1 for encoder VBI (1024 kB)
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.865743] ivtv1: Registered device video25 for encoder PCM (320 kB)
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.865745] ivtv1: Initialized card: WinTV PVR 500 (unit #2)
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.865799] ivtv: End initialization
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.913467] tda9887 4-0043: creating new instance
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.913470] tda9887 4-0043: tda988[5/6/7] found
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.914339] tuner 4-0043: Tuner 74 found with type(s) Radio TV.
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.920094] tuner 4-0061: Tuner -1 found with type(s) Radio TV.

Every thing appears OK for ivtv and cx18.


> Feb 11 09:22:21 mythtv-primary kernel: [ 12.944043] saa7164_downloadfirmware() no first image
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.944055] saa7164_downloadfirmware() Waiting for firmware upload (NXP7164-2010-03-10.1.fw)
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.964660] JFS: nTxBlock = 8192, nTxLock = 65536
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.982069] cs5345 3-004c: chip found @ 0x98 (cx18 i2c driver #0-0)
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.986133] tuner-simple 4-0061: creating new instance
> Feb 11 09:22:21 mythtv-primary kernel: [ 12.986136] tuner-simple 4-0061: type set to 85 (Philips FQ1236 MK5)
> Feb 11 09:22:21 mythtv-primary kernel: [ 13.000831] cx18-0: Registered device video2 for encoder MPEG (64 x 32.00 kB)
> Feb 11 09:22:21 mythtv-primary kernel: [ 13.000839] DVB: registering new adapter (cx18)
> Feb 11 09:22:21 mythtv-primary kernel: [ 13.001366] ppdev: user-space parallel port driver
> Feb 11 09:22:21 mythtv-primary kernel: [ 13.093375] saa7164_downloadfirmware() Upload failed. (file not found?)
> Feb 11 09:22:21 mythtv-primary kernel: [ 13.093380] Failed to boot firmware, no features registered

Your HVR-2250 probably isn't going to work, given those messages about a
missing firmware file.

> Feb 11 09:22:21 mythtv-primary kernel: [ 13.250727] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
> Feb 11 09:22:21 mythtv-primary kernel: [ 13.510643] EXT4-fs (sdd1): mounted filesystem with ordered data mode. Opts: (null)
> Feb 11 09:22:21 mythtv-primary kernel: [ 13.673594] ivtv0: Loaded v4l-cx2341x-enc.fw firmware (376836 bytes)
> Feb 11 09:22:21 mythtv-primary kernel: [ 13.701587] ivtv1: Loaded v4l-cx2341x-enc.fw firmware (376836 bytes)
> Feb 11 09:22:21 mythtv-primary kernel: [ 13.772527] k8temp 0000:00:18.3: Temperature readouts might be wrong - check erratum #141
> Feb 11 09:22:21 mythtv-primary kernel: [ 13.772807] EDAC amd64: DRAM ECC disabled.
> Feb 11 09:22:21 mythtv-primary kernel: [ 13.772813] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
> Feb 11 09:22:21 mythtv-primary kernel: [ 13.772814] Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
> Feb 11 09:22:21 mythtv-primary kernel: [ 13.772815] (Note that use of the override may cause unknown side effects.)
> Feb 11 09:22:21 mythtv-primary kernel: [ 13.872180] ivtv0: Encoder revision: 0x02060039
> Feb 11 09:22:21 mythtv-primary kernel: [ 13.883339] MXL5005S: Attached at address 0x63
> Feb 11 09:22:21 mythtv-primary kernel: [ 13.883344] DVB: registering adapter 0 frontend 0 (Samsung S5H1409 QAM/8VSB Frontend)...
> Feb 11 09:22:21 mythtv-primary kernel: [ 13.883461] cx18-0: DVB Frontend registered
> Feb 11 09:22:21 mythtv-primary kernel: [ 13.883464] cx18-0: Registered DVB adapter0 for TS (32 x 32.00 kB)
> Feb 11 09:22:21 mythtv-primary kernel: [ 13.883501] cx18-0: Registered device video34 for encoder YUV (20 x 101.25 kB)
> Feb 11 09:22:21 mythtv-primary kernel: [ 13.883540] cx18-0: Registered device vbi2 for encoder VBI (20 x 51984 bytes)
> Feb 11 09:22:21 mythtv-primary kernel: [ 13.883567] cx18-0: Registered device video26 for encoder PCM audio (256 x 4.00 kB)
> Feb 11 09:22:21 mythtv-primary kernel: [ 13.883570] cx18-0: Initialized card: Hauppauge HVR-1600
> Feb 11 09:22:21 mythtv-primary kernel: [ 13.883631] cx18: End initialization
> Feb 11 09:22:21 mythtv-primary kernel: [ 13.900395] ivtv1: Encoder revision: 0x02060039
> Feb 11 09:22:21 mythtv-primary kernel: [ 13.995615] cx18-alsa: module loading...
> Feb 11 09:22:21 mythtv-primary kernel: [ 14.162692] cx18-0: loaded v4l-cx23418-cpu.fw firmware (158332 bytes)
> Feb 11 09:22:21 mythtv-primary kernel: [ 14.413193] cx18-0: loaded v4l-cx23418-apu.fw firmware V00120000 (141200 bytes)
> Feb 11 09:22:21 mythtv-primary kernel: [ 14.472491] cx18-0: FW version: 0.0.74.0 (Release 2007/03/12)
> Feb 11 09:22:21 mythtv-primary kernel: [ 15.305943] nvidia: module license 'NVIDIA' taints kernel.
> Feb 11 09:22:21 mythtv-primary kernel: [ 15.305948] Disabling lock debugging due to kernel taint
> Feb 11 09:22:21 mythtv-primary kernel: [ 15.543106] ACPI: PCI Interrupt Link [SGRU] enabled at IRQ 20
> Feb 11 09:22:21 mythtv-primary kernel: [ 15.543114] nvidia 0000:03:00.0: PCI INT A -> Link[SGRU] -> GSI 20 (level, low) -> IRQ 20
> Feb 11 09:22:21 mythtv-primary kernel: [ 15.543122] nvidia 0000:03:00.0: setting latency timer to 64
> Feb 11 09:22:21 mythtv-primary kernel: [ 15.543127] vgaarb: device changed decodes: PCI:0000:03:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
> Feb 11 09:22:21 mythtv-primary kernel: [ 15.544170] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 290.10 Wed Nov 16 17:39:29 PST 2011
> Feb 11 09:22:21 mythtv-primary kernel: [ 15.738362] cx18-0 843: loaded v4l-cx23418-dig.fw firmware (16382 bytes)
> Feb 11 09:22:21 mythtv-primary kernel: [ 15.760120] cx18-0 843: verified load of v4l-cx23418-dig.fw firmware (16382 bytes)
> Feb 11 09:22:21 mythtv-primary kernel: [ 17.589877] cx25840 5-0044: loaded v4l-cx25840.fw firmware (16382 bytes)
> Feb 11 09:22:21 mythtv-primary kernel: [ 17.899715] RPC: Registered named UNIX socket transport module.
>
>
> Can anyone tell me if I have an actual firmware bug or if this is
> normal? Can anyone tell me how to test the card for sure to see if it
> is a defective card?

One last step is to verify that you do in fact have a video signal with
a known good devices (such as a TV). If you have RF analog or RF
digital reception problems, you may want to review this checklist as
well:

http://ivtvdriver.org/index.php/Howto:Improve_signal_quality

Regards,
Andy

>
> -Peter



_______________________________________________
ivtv-users mailing list
ivtv-users [at] ivtvdriver
http://ivtvdriver.org/mailman/listinfo/ivtv-users


peter.schneider at schneideris

Feb 11, 2012, 2:44 PM

Post #3 of 14 (1045 views)
Permalink
Re: Problems With additional tuners... [In reply to]
Thanks Andy,

You are THE MAN!!!! From the v4l2-ctl command I now have the analog working on both tuners for the 500 and now on the HVR-1600!!!

I am concerned about the HVR-2250 but that will be a debug to happen when I have an antenna built. At that time I can use the HVR-1600 digital tuner to test the antenna and then engage the HVR-2250.

Thanks again Andy.

-Peter


On 2012-02-11, at 3:02 PM, Andy Walls wrote:

> On Sat, 2012-02-11 at 11:02 -0700, Gmail wrote:
>> Hi All,
>>
>>
>> I am hoping someone can help me with some trouble shooting that I am
>> doing. I have a box with three Hauppauge cards installed (PVR-500,
>> HVR-2250, and the latest is a HVR 1600). Though I have the 2250
>> installed I have not built my antenna as of yet to bring it online.
>> My PVR-500 used to work with both tuners but then a couple years ago
>> the second unit just stopped working (no idea why and assumed over
>> time, after lots of attempts to try and revive, that it was just
>> dead). I happened across the HVR-1600 yesterday and thought it would
>> make a good addition for the second Analog tuner that I lost. The
>> problem is that it is providing the same static feed as the second
>> tuner from the PVR-500. After looking at the logs I am starting to
>> wonder if the problemI have is a firmware bug or something else and
>> could use some help. The reason I am turning to this list is because
>> of a line in the syslog in what appears to be the ivtv sequence.
>>
>>
>> Note: The Analog tuners are being used to capture video through the
>> s-video cable from my satellite tuners and the digital ones are for
>> future OTA HD.
>
> Please install v4l2-ctl (probably in a v4l2-utils package) and mplayer.
>
> Kill the mythbackend, if it is running.
>
> Then run v4l2-ctl --list-devices, to see what card corresponds to which
> devices nodes. For example:
>
> $ v4l2-ctl --list-devices
> Hauppauge HVR-1600 (PCI:0000:03:00.0):
> /dev/video0
> /dev/video24
> /dev/video32
> /dev/vbi0
>
> Hauppauge WinTV PVR-150 (PCI:0000:03:01.0):
> /dev/video2
> /dev/video26
> /dev/video34
> /dev/radio2
> /dev/vbi2
>
> Hauppauge HVR-1600 (PCI:0000:03:02.0):
> /dev/video1
> /dev/video25
> /dev/video33
> /dev/radio1
> /dev/vbi1
>
> On a device from which you wish to capture S-Video, set the proper input
> and analog TV standard using v4l2-ctl:
>
> $ v4l2-ctl -d /dev/video0 --list-inputs
> ioctl: VIDIOC_ENUMINPUT
> Input : 0
> Name : Tuner 1
> Type : 0x00000001
> Audioset : 0x00000007
> Tuner : 0x00000000
> Standard : 0x0000000000001000 (NTSC-M)
> Status : 0x00000000 (ok)
> Capabilities: 0x00000004 (SD presets)
>
> Input : 1
> Name : S-Video 1
> Type : 0x00000002
> Audioset : 0x00000007
> Tuner : 0x00000000
> Standard : 0x0000000000FFFFFF (PAL-B/B1/G/H/I/D/D1/K/M/N/Nc/60 NTSC-M/M-JP/443/M-KR SECAM-B/D/G/H/K/K1/L/Lc)
> Status : 0x00000000 (ok)
> Capabilities: 0x00000004 (SD presets)
>
> Input : 2
> Name : Composite 1
> Type : 0x00000002
> Audioset : 0x00000007
> Tuner : 0x00000000
> Standard : 0x0000000000FFFFFF (PAL-B/B1/G/H/I/D/D1/K/M/N/Nc/60 NTSC-M/M-JP/443/M-KR SECAM-B/D/G/H/K/K1/L/Lc)
> Status : 0x00000000 (ok)
> Capabilities: 0x00000004 (SD presets)
> [...]
>
> $ v4l2-ctl -d /dev/video0 --set-input=1
> Video input set to 1 (S-Video 1: ok)
>
> $ v4l2-ctl -d /dev/video0 --list-standards
> ioctl: VIDIOC_ENUMSTD
> Index : 0
> ID : 0x000000000000B000
> Name : NTSC
> Frame period: 1001/30000
> Frame lines : 525
>
> Index : 1
> ID : 0x0000000000001000
> Name : NTSC-M
> Frame period: 1001/30000
> Frame lines : 525
> [...]
>
> $ v4l2-ctl -d /dev/video0 --set-standard=1
> Standard set to 00001000
>
>
> Turn on your S-Video source, and then just capture an MPEG live with mplayer:
>
> $ mplayer /dev/video0 -cache 8192
>
> or capture a file for later playback
>
> $ cat /dev/video0 > foo.mpg
> ^C
> $ mplayer foo.mpg
>
>
>
>> Here is what I see on the two problematic analog tuners.
>
> Looks like an untuned tuner input driving the encoder, not S-Video. An
> S-Video input that is connected but has no signal is usually a solid
> grey or black screen.
>
>>
>> Here is some background information:
>
>> and:
>>
>>
>> cat /var/log/syslog|grep cx18
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.465299] cx18: Start initialization, version 1.5.0
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516868] cx18-0: Initializing card 0
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516871] cx18-0: Autodetected Hauppauge card
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.517062] cx18 0000:01:06.0: PCI INT A -> Link[LNKA] -> GSI 16 (level, low) -> IRQ 16
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.523272] cx18-0: cx23418 revision 01010000 (B)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.740991] cx18-0: Autodetected Hauppauge HVR-1600
>
> greping for 'cx18' will miss any error messages reltaed to the tuner
> chips and initialization. Anyway, the HVR-1600 lloks OK from what you
> provided.
>
>>
>> and what set my into this e-mail:
>>
>>
>>
>>
>>
>>
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.371758] Linux video capture interface: v2.00
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.382727] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.449074] ivtv: Start initialization, version 1.4.2
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.453711] parport_pc 00:05: reported by Plug and Play ACPI
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.453762] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.456724] [Firmware Bug]: ACPI(IGPU) defines _DOD but not _DOS
>
> Your computer's BIOS has an ACPI bug that is unrelated to the video
> capture cards, AFAICT.
>
>
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.457016] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:12/LNXVIDEO:00/input/input5
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.457108] ACPI: Video Device [IGPU] (multi-head: yes rom: no post: no)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.458546] ivtv0: Initializing card 0
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.458552] ivtv0: Autodetected Hauppauge card (cx23416 based)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.461226] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 17
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.461251] ivtv 0000:02:08.0: PCI INT A -> Link[LNKB] -> GSI 17 (level, low) -> IRQ 17
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.465299] cx18: Start initialization, version 1.5.0
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516569] tveeprom 2-0050: Hauppauge model 23552, rev E792, serial# 10603908
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516572] tveeprom 2-0050: tuner model is Philips FQ1236A MK4 (idx 92, type 57)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516575] tveeprom 2-0050: TV standards NTSC(M) (eeprom 0x08)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516577] tveeprom 2-0050: second tuner model is Philips TEA5768HL FM Radio (idx 101, type 62)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516580] tveeprom 2-0050: audio processor is CX25843 (idx 37)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516582] tveeprom 2-0050: decoder processor is CX25843 (idx 30)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516584] tveeprom 2-0050: has radio
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516586] ivtv0: Autodetected WinTV PVR 500 (unit #1)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516630] HDA Intel 0000:00:07.0: power state changed by ACPI to D0
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516635] HDA Intel 0000:00:07.0: power state changed by ACPI to D0
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516789] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 21
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516793] HDA Intel 0000:00:07.0: PCI INT A -> Link[LAZA] -> GSI 21 (level, low) -> IRQ 21
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516795] hda_intel: Disabling MSI
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516818] HDA Intel 0000:00:07.0: setting latency timer to 64
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516868] cx18-0: Initializing card 0
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516871] cx18-0: Autodetected Hauppauge card
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.517047] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 16
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.517062] cx18 0000:01:06.0: PCI INT A -> Link[LNKA] -> GSI 16 (level, low) -> IRQ 16
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.523272] cx18-0: cx23418 revision 01010000 (B)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.527518] cx25840 2-0044: cx25843-24 found @ 0x88 (ivtv i2c driver #0)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.552242] lp0: using parport0 (interrupt-driven).
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.559592] i2c-core: driver [tuner] using legacy suspend method
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.559595] i2c-core: driver [tuner] using legacy resume method
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.571404] tea5767 2-0060: type set to Philips TEA5767HN FM Radio
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.572716] tuner 2-0060: Tuner 62 found with type(s) Radio.
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.647194] tda9887 2-0043: creating new instance
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.647198] tda9887 2-0043: tda988[5/6/7] found
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.648262] tuner 2-0043: Tuner 74 found with type(s) Radio TV.
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.649550] EXT4-fs (sdc1): re-mounted. Opts: errors=remount-ro
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.661166] tuner 2-0061: Tuner -1 found with type(s) TV.
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.661266] MCE: In-kernel MCE decoding enabled.
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.662420] EDAC MC: Ver: 2.1.0
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.667708] AMD64 EDAC driver v3.4.0
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.669263] wm8775 2-001b: chip found @ 0x36 (ivtv i2c driver #0)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.679969] type=1400 audit(1328977336.392:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=765 comm="apparmor_parser"
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.680434] type=1400 audit(1328977336.396:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=765 comm="apparmor_parser"
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.680697] type=1400 audit(1328977336.396:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=765 comm="apparmor_parser"
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.683264] type=1400 audit(1328977336.396:5): apparmor="STATUS" operation="profile_load" name="/usr/sbin/ntpd" pid=786 comm="apparmor_parser"
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.691569] saa7164 driver loaded
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.695133] saa7164 0000:05:00.0: PCI INT A -> Link[LN2A] -> GSI 18 (level, low) -> IRQ 18
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.695958] CORE saa7164[0]: subsystem: 0070:8851, board: Hauppauge WinTV-HVR2250 [card=7,autodetected]
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.695962] saa7164[0]/0: found at 0000:05:00.0, rev: 129, irq: 18, latency: 0, mmio: 0xfe800000
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.695968] saa7164 0000:05:00.0: setting latency timer to 64
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.698088] tuner-simple 2-0061: creating new instance
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.698093] tuner-simple 2-0061: type set to 57 (Philips FQ1236A MK4)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.699764] ivtv0: Registered device video0 for encoder MPG (4096 kB)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.699792] ivtv0: Registered device video32 for encoder YUV (2048 kB)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.699818] ivtv0: Registered device vbi0 for encoder VBI (1024 kB)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.699841] ivtv0: Registered device video24 for encoder PCM (320 kB)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.699866] ivtv0: Registered device radio0 for encoder radio
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.699868] ivtv0: Initialized card: WinTV PVR 500 (unit #1)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.740974] tveeprom 3-0050: Hauppauge model 74041, rev C6G8, serial# 7255283
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.740977] tveeprom 3-0050: MAC address is 00:0d:fe:6e:b4:f3
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.740979] tveeprom 3-0050: tuner model is TCL M30WTP-4N-E (idx 168, type 85)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.740982] tveeprom 3-0050: TV standards NTSC(M) (eeprom 0x08)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.740984] tveeprom 3-0050: audio processor is CX23418 (idx 38)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.740986] tveeprom 3-0050: decoder processor is CX23418 (idx 31)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.740988] tveeprom 3-0050: has no radio, has IR receiver, has IR transmitter
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.740991] cx18-0: Autodetected Hauppauge HVR-1600
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.740993] cx18-0: Simultaneous Digital and Analog TV capture supported
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.748153] ivtv1: Initializing card 1
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.748158] ivtv1: Autodetected Hauppauge card (cx23416 based)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.749970] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 19
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.749978] ivtv 0000:02:09.0: PCI INT A -> Link[LNKC] -> GSI 19 (level, low) -> IRQ 19
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.805055] tveeprom 5-0050: Hauppauge model 23552, rev E792, serial# 10603908
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.805058] tveeprom 5-0050: tuner model is Philips FQ1236A MK4 (idx 92, type 57)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.805060] tveeprom 5-0050: TV standards NTSC(M) (eeprom 0x08)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.805063] tveeprom 5-0050: second tuner model is Philips TEA5768HL FM Radio (idx 101, type 62)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.805065] tveeprom 5-0050: audio processor is CX25843 (idx 37)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.805067] tveeprom 5-0050: decoder processor is CX25843 (idx 30)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.805069] tveeprom 5-0050: has radio
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.805071] ivtv1: Correcting tveeprom data: no radio present on second unit
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.805073] ivtv1: Autodetected WinTV PVR 500 (unit #2)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.811719] cx25840 5-0044: cx25843-24 found @ 0x88 (ivtv i2c driver #1)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.833014] tda9887 5-0043: creating new instance
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.833017] tda9887 5-0043: tda988[5/6/7] found
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.834052] tuner 5-0043: Tuner 74 found with type(s) Radio TV.
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.839893] tuner 5-0061: Tuner -1 found with type(s) Radio TV.
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.845534] wm8775 5-001b: chip found @ 0x36 (ivtv i2c driver #1)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.863936] tuner-simple 5-0061: creating new instance
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.863940] tuner-simple 5-0061: type set to 57 (Philips FQ1236A MK4)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.865665] ivtv1: Registered device video1 for encoder MPG (4096 kB)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.865692] ivtv1: Registered device video33 for encoder YUV (2048 kB)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.865717] ivtv1: Registered device vbi1 for encoder VBI (1024 kB)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.865743] ivtv1: Registered device video25 for encoder PCM (320 kB)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.865745] ivtv1: Initialized card: WinTV PVR 500 (unit #2)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.865799] ivtv: End initialization
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.913467] tda9887 4-0043: creating new instance
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.913470] tda9887 4-0043: tda988[5/6/7] found
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.914339] tuner 4-0043: Tuner 74 found with type(s) Radio TV.
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.920094] tuner 4-0061: Tuner -1 found with type(s) Radio TV.
>
> Every thing appears OK for ivtv and cx18.
>
>
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.944043] saa7164_downloadfirmware() no first image
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.944055] saa7164_downloadfirmware() Waiting for firmware upload (NXP7164-2010-03-10.1.fw)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.964660] JFS: nTxBlock = 8192, nTxLock = 65536
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.982069] cs5345 3-004c: chip found @ 0x98 (cx18 i2c driver #0-0)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.986133] tuner-simple 4-0061: creating new instance
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.986136] tuner-simple 4-0061: type set to 85 (Philips FQ1236 MK5)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.000831] cx18-0: Registered device video2 for encoder MPEG (64 x 32.00 kB)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.000839] DVB: registering new adapter (cx18)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.001366] ppdev: user-space parallel port driver
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.093375] saa7164_downloadfirmware() Upload failed. (file not found?)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.093380] Failed to boot firmware, no features registered
>
> Your HVR-2250 probably isn't going to work, given those messages about a
> missing firmware file.
>
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.250727] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.510643] EXT4-fs (sdd1): mounted filesystem with ordered data mode. Opts: (null)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.673594] ivtv0: Loaded v4l-cx2341x-enc.fw firmware (376836 bytes)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.701587] ivtv1: Loaded v4l-cx2341x-enc.fw firmware (376836 bytes)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.772527] k8temp 0000:00:18.3: Temperature readouts might be wrong - check erratum #141
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.772807] EDAC amd64: DRAM ECC disabled.
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.772813] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.772814] Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.772815] (Note that use of the override may cause unknown side effects.)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.872180] ivtv0: Encoder revision: 0x02060039
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.883339] MXL5005S: Attached at address 0x63
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.883344] DVB: registering adapter 0 frontend 0 (Samsung S5H1409 QAM/8VSB Frontend)...
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.883461] cx18-0: DVB Frontend registered
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.883464] cx18-0: Registered DVB adapter0 for TS (32 x 32.00 kB)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.883501] cx18-0: Registered device video34 for encoder YUV (20 x 101.25 kB)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.883540] cx18-0: Registered device vbi2 for encoder VBI (20 x 51984 bytes)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.883567] cx18-0: Registered device video26 for encoder PCM audio (256 x 4.00 kB)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.883570] cx18-0: Initialized card: Hauppauge HVR-1600
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.883631] cx18: End initialization
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.900395] ivtv1: Encoder revision: 0x02060039
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.995615] cx18-alsa: module loading...
>> Feb 11 09:22:21 mythtv-primary kernel: [ 14.162692] cx18-0: loaded v4l-cx23418-cpu.fw firmware (158332 bytes)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 14.413193] cx18-0: loaded v4l-cx23418-apu.fw firmware V00120000 (141200 bytes)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 14.472491] cx18-0: FW version: 0.0.74.0 (Release 2007/03/12)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 15.305943] nvidia: module license 'NVIDIA' taints kernel.
>> Feb 11 09:22:21 mythtv-primary kernel: [ 15.305948] Disabling lock debugging due to kernel taint
>> Feb 11 09:22:21 mythtv-primary kernel: [ 15.543106] ACPI: PCI Interrupt Link [SGRU] enabled at IRQ 20
>> Feb 11 09:22:21 mythtv-primary kernel: [ 15.543114] nvidia 0000:03:00.0: PCI INT A -> Link[SGRU] -> GSI 20 (level, low) -> IRQ 20
>> Feb 11 09:22:21 mythtv-primary kernel: [ 15.543122] nvidia 0000:03:00.0: setting latency timer to 64
>> Feb 11 09:22:21 mythtv-primary kernel: [ 15.543127] vgaarb: device changed decodes: PCI:0000:03:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
>> Feb 11 09:22:21 mythtv-primary kernel: [ 15.544170] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 290.10 Wed Nov 16 17:39:29 PST 2011
>> Feb 11 09:22:21 mythtv-primary kernel: [ 15.738362] cx18-0 843: loaded v4l-cx23418-dig.fw firmware (16382 bytes)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 15.760120] cx18-0 843: verified load of v4l-cx23418-dig.fw firmware (16382 bytes)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 17.589877] cx25840 5-0044: loaded v4l-cx25840.fw firmware (16382 bytes)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 17.899715] RPC: Registered named UNIX socket transport module.
>>
>>
>> Can anyone tell me if I have an actual firmware bug or if this is
>> normal? Can anyone tell me how to test the card for sure to see if it
>> is a defective card?
>
> One last step is to verify that you do in fact have a video signal with
> a known good devices (such as a TV). If you have RF analog or RF
> digital reception problems, you may want to review this checklist as
> well:
>
> http://ivtvdriver.org/index.php/Howto:Improve_signal_quality
>
> Regards,
> Andy
>
>>
>> -Peter
>
>
>
> _______________________________________________
> ivtv-users mailing list
> ivtv-users [at] ivtvdriver
> http://ivtvdriver.org/mailman/listinfo/ivtv-users


_______________________________________________
ivtv-users mailing list
ivtv-users [at] ivtvdriver
http://ivtvdriver.org/mailman/listinfo/ivtv-users


awalls at md

Feb 11, 2012, 3:09 PM

Post #4 of 14 (1055 views)
Permalink
Re: Problems With additional tuners... [In reply to]
On Sat, 2012-02-11 at 15:44 -0700, Peter Schneider wrote:
> Thanks Andy,
>
> You are THE MAN!!!! From the v4l2-ctl command I now have the analog
> working on both tuners for the 500 and now on the HVR-1600!!!
>
> I am concerned about the HVR-2250 but that will be a debug to happen
> when I have an antenna built. At that time I can use the HVR-1600
> digital tuner to test the antenna and then engage the HVR-2250.
>
> Thanks again Andy.

You're welcome. :)

-Andy

> -Peter
>
>
> On 2012-02-11, at 3:02 PM, Andy Walls wrote:
>
> > On Sat, 2012-02-11 at 11:02 -0700, Gmail wrote:
> >> Hi All,

> >>
> >> Note: The Analog tuners are being used to capture video through the
> >> s-video cable from my satellite tuners and the digital ones are for
> >> future OTA HD.
> >
> > Please install v4l2-ctl (probably in a v4l2-utils package) and mplayer.
> >
> > Kill the mythbackend, if it is running.
> >
> > Then run v4l2-ctl --list-devices, to see what card corresponds to which
> > devices nodes. For example:
> >
> > $ v4l2-ctl --list-devices
> > Hauppauge HVR-1600 (PCI:0000:03:00.0):
> > /dev/video0
> > /dev/video24
> > /dev/video32
> > /dev/vbi0
> >
> > Hauppauge WinTV PVR-150 (PCI:0000:03:01.0):
> > /dev/video2
> > /dev/video26
> > /dev/video34
> > /dev/radio2
> > /dev/vbi2
> >
> > Hauppauge HVR-1600 (PCI:0000:03:02.0):
> > /dev/video1
> > /dev/video25
> > /dev/video33
> > /dev/radio1
> > /dev/vbi1
> >
> > On a device from which you wish to capture S-Video, set the proper input
> > and analog TV standard using v4l2-ctl:
> >
> > $ v4l2-ctl -d /dev/video0 --list-inputs
> > ioctl: VIDIOC_ENUMINPUT
> > Input : 0
> > Name : Tuner 1
> > Type : 0x00000001
> > Audioset : 0x00000007
> > Tuner : 0x00000000
> > Standard : 0x0000000000001000 (NTSC-M)
> > Status : 0x00000000 (ok)
> > Capabilities: 0x00000004 (SD presets)
> >
> > Input : 1
> > Name : S-Video 1
> > Type : 0x00000002
> > Audioset : 0x00000007
> > Tuner : 0x00000000
> > Standard : 0x0000000000FFFFFF (PAL-B/B1/G/H/I/D/D1/K/M/N/Nc/60 NTSC-M/M-JP/443/M-KR SECAM-B/D/G/H/K/K1/L/Lc)
> > Status : 0x00000000 (ok)
> > Capabilities: 0x00000004 (SD presets)
> >
> > Input : 2
> > Name : Composite 1
> > Type : 0x00000002
> > Audioset : 0x00000007
> > Tuner : 0x00000000
> > Standard : 0x0000000000FFFFFF (PAL-B/B1/G/H/I/D/D1/K/M/N/Nc/60 NTSC-M/M-JP/443/M-KR SECAM-B/D/G/H/K/K1/L/Lc)
> > Status : 0x00000000 (ok)
> > Capabilities: 0x00000004 (SD presets)
> > [...]
> >
> > $ v4l2-ctl -d /dev/video0 --set-input=1
> > Video input set to 1 (S-Video 1: ok)
> >
> > $ v4l2-ctl -d /dev/video0 --list-standards
> > ioctl: VIDIOC_ENUMSTD
> > Index : 0
> > ID : 0x000000000000B000
> > Name : NTSC
> > Frame period: 1001/30000
> > Frame lines : 525
> >
> > Index : 1
> > ID : 0x0000000000001000
> > Name : NTSC-M
> > Frame period: 1001/30000
> > Frame lines : 525
> > [...]
> >
> > $ v4l2-ctl -d /dev/video0 --set-standard=1
> > Standard set to 00001000
> >
> >
> > Turn on your S-Video source, and then just capture an MPEG live with mplayer:
> >
> > $ mplayer /dev/video0 -cache 8192
> >
> > or capture a file for later playback
> >
> > $ cat /dev/video0 > foo.mpg
> > ^C
> > $ mplayer foo.mpg
> >
> >
> >
> >> Here is what I see on the two problematic analog tuners.
> >
> > Looks like an untuned tuner input driving the encoder, not S-Video. An
> > S-Video input that is connected but has no signal is usually a solid
> > grey or black screen.
> >

> > One last step is to verify that you do in fact have a video signal with
> > a known good devices (such as a TV). If you have RF analog or RF
> > digital reception problems, you may want to review this checklist as
> > well:
> >
> > http://ivtvdriver.org/index.php/Howto:Improve_signal_quality
> >
> > Regards,
> > Andy
> >
> >>
> >> -Peter



_______________________________________________
ivtv-users mailing list
ivtv-users [at] ivtvdriver
http://ivtvdriver.org/mailman/listinfo/ivtv-users


peter.schneider at schneideris

Feb 11, 2012, 5:50 PM

Post #5 of 14 (1050 views)
Permalink
Re: Problems With additional tuners... [In reply to]
Andy,

With the second PVR-500 tuner I am not getting any audio. Do you have any idea if this might be related to the v4l2 setup?

-Peter

On 2012-02-11, at 4:09 PM, Andy Walls wrote:

> On Sat, 2012-02-11 at 15:44 -0700, Peter Schneider wrote:
>> Thanks Andy,
>>
>> You are THE MAN!!!! From the v4l2-ctl command I now have the analog
>> working on both tuners for the 500 and now on the HVR-1600!!!
>>
>> I am concerned about the HVR-2250 but that will be a debug to happen
>> when I have an antenna built. At that time I can use the HVR-1600
>> digital tuner to test the antenna and then engage the HVR-2250.
>>
>> Thanks again Andy.
>
> You're welcome. :)
>
> -Andy
>
>> -Peter
>>
>>
>> On 2012-02-11, at 3:02 PM, Andy Walls wrote:
>>
>>> On Sat, 2012-02-11 at 11:02 -0700, Gmail wrote:
>>>> Hi All,
>
>>>>
>>>> Note: The Analog tuners are being used to capture video through the
>>>> s-video cable from my satellite tuners and the digital ones are for
>>>> future OTA HD.
>>>
>>> Please install v4l2-ctl (probably in a v4l2-utils package) and mplayer.
>>>
>>> Kill the mythbackend, if it is running.
>>>
>>> Then run v4l2-ctl --list-devices, to see what card corresponds to which
>>> devices nodes. For example:
>>>
>>> $ v4l2-ctl --list-devices
>>> Hauppauge HVR-1600 (PCI:0000:03:00.0):
>>> /dev/video0
>>> /dev/video24
>>> /dev/video32
>>> /dev/vbi0
>>>
>>> Hauppauge WinTV PVR-150 (PCI:0000:03:01.0):
>>> /dev/video2
>>> /dev/video26
>>> /dev/video34
>>> /dev/radio2
>>> /dev/vbi2
>>>
>>> Hauppauge HVR-1600 (PCI:0000:03:02.0):
>>> /dev/video1
>>> /dev/video25
>>> /dev/video33
>>> /dev/radio1
>>> /dev/vbi1
>>>
>>> On a device from which you wish to capture S-Video, set the proper input
>>> and analog TV standard using v4l2-ctl:
>>>
>>> $ v4l2-ctl -d /dev/video0 --list-inputs
>>> ioctl: VIDIOC_ENUMINPUT
>>> Input : 0
>>> Name : Tuner 1
>>> Type : 0x00000001
>>> Audioset : 0x00000007
>>> Tuner : 0x00000000
>>> Standard : 0x0000000000001000 (NTSC-M)
>>> Status : 0x00000000 (ok)
>>> Capabilities: 0x00000004 (SD presets)
>>>
>>> Input : 1
>>> Name : S-Video 1
>>> Type : 0x00000002
>>> Audioset : 0x00000007
>>> Tuner : 0x00000000
>>> Standard : 0x0000000000FFFFFF (PAL-B/B1/G/H/I/D/D1/K/M/N/Nc/60 NTSC-M/M-JP/443/M-KR SECAM-B/D/G/H/K/K1/L/Lc)
>>> Status : 0x00000000 (ok)
>>> Capabilities: 0x00000004 (SD presets)
>>>
>>> Input : 2
>>> Name : Composite 1
>>> Type : 0x00000002
>>> Audioset : 0x00000007
>>> Tuner : 0x00000000
>>> Standard : 0x0000000000FFFFFF (PAL-B/B1/G/H/I/D/D1/K/M/N/Nc/60 NTSC-M/M-JP/443/M-KR SECAM-B/D/G/H/K/K1/L/Lc)
>>> Status : 0x00000000 (ok)
>>> Capabilities: 0x00000004 (SD presets)
>>> [...]
>>>
>>> $ v4l2-ctl -d /dev/video0 --set-input=1
>>> Video input set to 1 (S-Video 1: ok)
>>>
>>> $ v4l2-ctl -d /dev/video0 --list-standards
>>> ioctl: VIDIOC_ENUMSTD
>>> Index : 0
>>> ID : 0x000000000000B000
>>> Name : NTSC
>>> Frame period: 1001/30000
>>> Frame lines : 525
>>>
>>> Index : 1
>>> ID : 0x0000000000001000
>>> Name : NTSC-M
>>> Frame period: 1001/30000
>>> Frame lines : 525
>>> [...]
>>>
>>> $ v4l2-ctl -d /dev/video0 --set-standard=1
>>> Standard set to 00001000
>>>
>>>
>>> Turn on your S-Video source, and then just capture an MPEG live with mplayer:
>>>
>>> $ mplayer /dev/video0 -cache 8192
>>>
>>> or capture a file for later playback
>>>
>>> $ cat /dev/video0 > foo.mpg
>>> ^C
>>> $ mplayer foo.mpg
>>>
>>>
>>>
>>>> Here is what I see on the two problematic analog tuners.
>>>
>>> Looks like an untuned tuner input driving the encoder, not S-Video. An
>>> S-Video input that is connected but has no signal is usually a solid
>>> grey or black screen.
>>>
>
>>> One last step is to verify that you do in fact have a video signal with
>>> a known good devices (such as a TV). If you have RF analog or RF
>>> digital reception problems, you may want to review this checklist as
>>> well:
>>>
>>> http://ivtvdriver.org/index.php/Howto:Improve_signal_quality
>>>
>>> Regards,
>>> Andy
>>>
>>>>
>>>> -Peter
>
>
>
> _______________________________________________
> ivtv-users mailing list
> ivtv-users [at] ivtvdriver
> http://ivtvdriver.org/mailman/listinfo/ivtv-users


_______________________________________________
ivtv-users mailing list
ivtv-users [at] ivtvdriver
http://ivtvdriver.org/mailman/listinfo/ivtv-users


awalls at md

Feb 11, 2012, 6:45 PM

Post #6 of 14 (1052 views)
Permalink
Re: Problems With additional tuners... [In reply to]
Peter Schneider <peter.schneider [at] schneideris> wrote:

>Andy,
>
>With the second PVR-500 tuner I am not getting any audio. Do you have
>any idea if this might be related to the v4l2 setup?
>
>-Peter
>
>On 2012-02-11, at 4:09 PM, Andy Walls wrote:
>
>> On Sat, 2012-02-11 at 15:44 -0700, Peter Schneider wrote:
>>> Thanks Andy,
>>>
>>> You are THE MAN!!!! From the v4l2-ctl command I now have the analog
>>> working on both tuners for the 500 and now on the HVR-1600!!!
>>>
>>> I am concerned about the HVR-2250 but that will be a debug to happen
>>> when I have an antenna built. At that time I can use the HVR-1600
>>> digital tuner to test the antenna and then engage the HVR-2250.
>>>
>>> Thanks again Andy.
>>
>> You're welcome. :)
>>
>> -Andy
>>
>>> -Peter
>>>
>>>
>>> On 2012-02-11, at 3:02 PM, Andy Walls wrote:
>>>
>>>> On Sat, 2012-02-11 at 11:02 -0700, Gmail wrote:
>>>>> Hi All,
>>
>>>>>
>>>>> Note: The Analog tuners are being used to capture video through
>the
>>>>> s-video cable from my satellite tuners and the digital ones are
>for
>>>>> future OTA HD.
>>>>
>>>> Please install v4l2-ctl (probably in a v4l2-utils package) and
>mplayer.
>>>>
>>>> Kill the mythbackend, if it is running.
>>>>
>>>> Then run v4l2-ctl --list-devices, to see what card corresponds to
>which
>>>> devices nodes. For example:
>>>>
>>>> $ v4l2-ctl --list-devices
>>>> Hauppauge HVR-1600 (PCI:0000:03:00.0):
>>>> /dev/video0
>>>> /dev/video24
>>>> /dev/video32
>>>> /dev/vbi0
>>>>
>>>> Hauppauge WinTV PVR-150 (PCI:0000:03:01.0):
>>>> /dev/video2
>>>> /dev/video26
>>>> /dev/video34
>>>> /dev/radio2
>>>> /dev/vbi2
>>>>
>>>> Hauppauge HVR-1600 (PCI:0000:03:02.0):
>>>> /dev/video1
>>>> /dev/video25
>>>> /dev/video33
>>>> /dev/radio1
>>>> /dev/vbi1
>>>>
>>>> On a device from which you wish to capture S-Video, set the proper
>input
>>>> and analog TV standard using v4l2-ctl:
>>>>
>>>> $ v4l2-ctl -d /dev/video0 --list-inputs
>>>> ioctl: VIDIOC_ENUMINPUT
>>>> Input : 0
>>>> Name : Tuner 1
>>>> Type : 0x00000001
>>>> Audioset : 0x00000007
>>>> Tuner : 0x00000000
>>>> Standard : 0x0000000000001000 (NTSC-M)
>>>> Status : 0x00000000 (ok)
>>>> Capabilities: 0x00000004 (SD presets)
>>>>
>>>> Input : 1
>>>> Name : S-Video 1
>>>> Type : 0x00000002
>>>> Audioset : 0x00000007
>>>> Tuner : 0x00000000
>>>> Standard : 0x0000000000FFFFFF
>(PAL-B/B1/G/H/I/D/D1/K/M/N/Nc/60 NTSC-M/M-JP/443/M-KR
>SECAM-B/D/G/H/K/K1/L/Lc)
>>>> Status : 0x00000000 (ok)
>>>> Capabilities: 0x00000004 (SD presets)
>>>>
>>>> Input : 2
>>>> Name : Composite 1
>>>> Type : 0x00000002
>>>> Audioset : 0x00000007
>>>> Tuner : 0x00000000
>>>> Standard : 0x0000000000FFFFFF
>(PAL-B/B1/G/H/I/D/D1/K/M/N/Nc/60 NTSC-M/M-JP/443/M-KR
>SECAM-B/D/G/H/K/K1/L/Lc)
>>>> Status : 0x00000000 (ok)
>>>> Capabilities: 0x00000004 (SD presets)
>>>> [...]
>>>>
>>>> $ v4l2-ctl -d /dev/video0 --set-input=1
>>>> Video input set to 1 (S-Video 1: ok)
>>>>
>>>> $ v4l2-ctl -d /dev/video0 --list-standards
>>>> ioctl: VIDIOC_ENUMSTD
>>>> Index : 0
>>>> ID : 0x000000000000B000
>>>> Name : NTSC
>>>> Frame period: 1001/30000
>>>> Frame lines : 525
>>>>
>>>> Index : 1
>>>> ID : 0x0000000000001000
>>>> Name : NTSC-M
>>>> Frame period: 1001/30000
>>>> Frame lines : 525
>>>> [...]
>>>>
>>>> $ v4l2-ctl -d /dev/video0 --set-standard=1
>>>> Standard set to 00001000
>>>>
>>>>
>>>> Turn on your S-Video source, and then just capture an MPEG live
>with mplayer:
>>>>
>>>> $ mplayer /dev/video0 -cache 8192
>>>>
>>>> or capture a file for later playback
>>>>
>>>> $ cat /dev/video0 > foo.mpg
>>>> ^C
>>>> $ mplayer foo.mpg
>>>>
>>>>
>>>>
>>>>> Here is what I see on the two problematic analog tuners.
>>>>
>>>> Looks like an untuned tuner input driving the encoder, not S-Video.
> An
>>>> S-Video input that is connected but has no signal is usually a
>solid
>>>> grey or black screen.
>>>>
>>
>>>> One last step is to verify that you do in fact have a video signal
>with
>>>> a known good devices (such as a TV). If you have RF analog or RF
>>>> digital reception problems, you may want to review this checklist
>as
>>>> well:
>>>>
>>>> http://ivtvdriver.org/index.php/Howto:Improve_signal_quality
>>>>
>>>> Regards,
>>>> Andy
>>>>
>>>>>
>>>>> -Peter
>>
>>
>>
>> _______________________________________________
>> ivtv-users mailing list
>> ivtv-users [at] ivtvdriver
>> http://ivtvdriver.org/mailman/listinfo/ivtv-users
>
>
>_______________________________________________
>ivtv-users mailing list
>ivtv-users [at] ivtvdriver
>http://ivtvdriver.org/mailman/listinfo/ivtv-users

No audio for the 2nd RF input means there's a problem with the 2nd analog tuner can or a problem with the second CX25843 chip.

No audio for the 2nd S Video input usually means you don't have the proper extra audio cable/bracket installed. There were at least two different versions of that cable/bracket for the 500 and 150 variants.

v4l2-ctl -d /dev/videoN --log-status

Should tell you what audio input is being used and if the RF broadcast audio decoding microcontroller is running or muted. V4l2-ctl can also set the audio input explicitly different than the one normally paired with a particular video connector.

v4l2-ctl --help

Lists all the options.

-Andy

_______________________________________________
ivtv-users mailing list
ivtv-users [at] ivtvdriver
http://ivtvdriver.org/mailman/listinfo/ivtv-users


peter.schneider at schneideris

Feb 12, 2012, 7:52 AM

Post #7 of 14 (1046 views)
Permalink
Re: Problems With additional tuners... [In reply to]
Hi Andy,

I am thinking that there must in fact be something wrong with either a cable or the board for the second connection. All the settings are identical between both Video0 and Video1 except for the s-video input (1 & 3 respectively) and the audio input (1 & 2 respectively). I confirmed the cables, switched sat boxes as a test, and no sound on number 2.

I will have to crack open the box next to see if something there is the issue. For now though I am going to try and figure out how to configure MythTV to work with the HVR-1600 (at the moment it is not seeing it so my config is wrong in Myth).

Thanks again for your help and the great education.

-Peter


On 2012-02-11, at 7:45 PM, Andy Walls wrote:

> Peter Schneider <peter.schneider [at] schneideris> wrote:
>
>> Andy,
>>
>> With the second PVR-500 tuner I am not getting any audio. Do you have
>> any idea if this might be related to the v4l2 setup?
>>
>> -Peter
>>
>> On 2012-02-11, at 4:09 PM, Andy Walls wrote:
>>
>>> On Sat, 2012-02-11 at 15:44 -0700, Peter Schneider wrote:
>>>> Thanks Andy,
>>>>
>>>> You are THE MAN!!!! From the v4l2-ctl command I now have the analog
>>>> working on both tuners for the 500 and now on the HVR-1600!!!
>>>>
>>>> I am concerned about the HVR-2250 but that will be a debug to happen
>>>> when I have an antenna built. At that time I can use the HVR-1600
>>>> digital tuner to test the antenna and then engage the HVR-2250.
>>>>
>>>> Thanks again Andy.
>>>
>>> You're welcome. :)
>>>
>>> -Andy
>>>
>>>> -Peter
>>>>
>>>>
>>>> On 2012-02-11, at 3:02 PM, Andy Walls wrote:
>>>>
>>>>> On Sat, 2012-02-11 at 11:02 -0700, Gmail wrote:
>>>>>> Hi All,
>>>
>>>>>>
>>>>>> Note: The Analog tuners are being used to capture video through
>> the
>>>>>> s-video cable from my satellite tuners and the digital ones are
>> for
>>>>>> future OTA HD.
>>>>>
>>>>> Please install v4l2-ctl (probably in a v4l2-utils package) and
>> mplayer.
>>>>>
>>>>> Kill the mythbackend, if it is running.
>>>>>
>>>>> Then run v4l2-ctl --list-devices, to see what card corresponds to
>> which
>>>>> devices nodes. For example:
>>>>>
>>>>> $ v4l2-ctl --list-devices
>>>>> Hauppauge HVR-1600 (PCI:0000:03:00.0):
>>>>> /dev/video0
>>>>> /dev/video24
>>>>> /dev/video32
>>>>> /dev/vbi0
>>>>>
>>>>> Hauppauge WinTV PVR-150 (PCI:0000:03:01.0):
>>>>> /dev/video2
>>>>> /dev/video26
>>>>> /dev/video34
>>>>> /dev/radio2
>>>>> /dev/vbi2
>>>>>
>>>>> Hauppauge HVR-1600 (PCI:0000:03:02.0):
>>>>> /dev/video1
>>>>> /dev/video25
>>>>> /dev/video33
>>>>> /dev/radio1
>>>>> /dev/vbi1
>>>>>
>>>>> On a device from which you wish to capture S-Video, set the proper
>> input
>>>>> and analog TV standard using v4l2-ctl:
>>>>>
>>>>> $ v4l2-ctl -d /dev/video0 --list-inputs
>>>>> ioctl: VIDIOC_ENUMINPUT
>>>>> Input : 0
>>>>> Name : Tuner 1
>>>>> Type : 0x00000001
>>>>> Audioset : 0x00000007
>>>>> Tuner : 0x00000000
>>>>> Standard : 0x0000000000001000 (NTSC-M)
>>>>> Status : 0x00000000 (ok)
>>>>> Capabilities: 0x00000004 (SD presets)
>>>>>
>>>>> Input : 1
>>>>> Name : S-Video 1
>>>>> Type : 0x00000002
>>>>> Audioset : 0x00000007
>>>>> Tuner : 0x00000000
>>>>> Standard : 0x0000000000FFFFFF
>> (PAL-B/B1/G/H/I/D/D1/K/M/N/Nc/60 NTSC-M/M-JP/443/M-KR
>> SECAM-B/D/G/H/K/K1/L/Lc)
>>>>> Status : 0x00000000 (ok)
>>>>> Capabilities: 0x00000004 (SD presets)
>>>>>
>>>>> Input : 2
>>>>> Name : Composite 1
>>>>> Type : 0x00000002
>>>>> Audioset : 0x00000007
>>>>> Tuner : 0x00000000
>>>>> Standard : 0x0000000000FFFFFF
>> (PAL-B/B1/G/H/I/D/D1/K/M/N/Nc/60 NTSC-M/M-JP/443/M-KR
>> SECAM-B/D/G/H/K/K1/L/Lc)
>>>>> Status : 0x00000000 (ok)
>>>>> Capabilities: 0x00000004 (SD presets)
>>>>> [...]
>>>>>
>>>>> $ v4l2-ctl -d /dev/video0 --set-input=1
>>>>> Video input set to 1 (S-Video 1: ok)
>>>>>
>>>>> $ v4l2-ctl -d /dev/video0 --list-standards
>>>>> ioctl: VIDIOC_ENUMSTD
>>>>> Index : 0
>>>>> ID : 0x000000000000B000
>>>>> Name : NTSC
>>>>> Frame period: 1001/30000
>>>>> Frame lines : 525
>>>>>
>>>>> Index : 1
>>>>> ID : 0x0000000000001000
>>>>> Name : NTSC-M
>>>>> Frame period: 1001/30000
>>>>> Frame lines : 525
>>>>> [...]
>>>>>
>>>>> $ v4l2-ctl -d /dev/video0 --set-standard=1
>>>>> Standard set to 00001000
>>>>>
>>>>>
>>>>> Turn on your S-Video source, and then just capture an MPEG live
>> with mplayer:
>>>>>
>>>>> $ mplayer /dev/video0 -cache 8192
>>>>>
>>>>> or capture a file for later playback
>>>>>
>>>>> $ cat /dev/video0 > foo.mpg
>>>>> ^C
>>>>> $ mplayer foo.mpg
>>>>>
>>>>>
>>>>>
>>>>>> Here is what I see on the two problematic analog tuners.
>>>>>
>>>>> Looks like an untuned tuner input driving the encoder, not S-Video.
>> An
>>>>> S-Video input that is connected but has no signal is usually a
>> solid
>>>>> grey or black screen.
>>>>>
>>>
>>>>> One last step is to verify that you do in fact have a video signal
>> with
>>>>> a known good devices (such as a TV). If you have RF analog or RF
>>>>> digital reception problems, you may want to review this checklist
>> as
>>>>> well:
>>>>>
>>>>> http://ivtvdriver.org/index.php/Howto:Improve_signal_quality
>>>>>
>>>>> Regards,
>>>>> Andy
>>>>>
>>>>>>
>>>>>> -Peter
>>>
>>>
>>>
>>> _______________________________________________
>>> ivtv-users mailing list
>>> ivtv-users [at] ivtvdriver
>>> http://ivtvdriver.org/mailman/listinfo/ivtv-users
>>
>>
>> _______________________________________________
>> ivtv-users mailing list
>> ivtv-users [at] ivtvdriver
>> http://ivtvdriver.org/mailman/listinfo/ivtv-users
>
> No audio for the 2nd RF input means there's a problem with the 2nd analog tuner can or a problem with the second CX25843 chip.
>
> No audio for the 2nd S Video input usually means you don't have the proper extra audio cable/bracket installed. There were at least two different versions of that cable/bracket for the 500 and 150 variants.
>
> v4l2-ctl -d /dev/videoN --log-status
>
> Should tell you what audio input is being used and if the RF broadcast audio decoding microcontroller is running or muted. V4l2-ctl can also set the audio input explicitly different than the one normally paired with a particular video connector.
>
> v4l2-ctl --help
>
> Lists all the options.
>
> -Andy
>
> _______________________________________________
> ivtv-users mailing list
> ivtv-users [at] ivtvdriver
> http://ivtvdriver.org/mailman/listinfo/ivtv-users


_______________________________________________
ivtv-users mailing list
ivtv-users [at] ivtvdriver
http://ivtvdriver.org/mailman/listinfo/ivtv-users


awalls at md

Feb 12, 2012, 10:43 AM

Post #8 of 14 (1044 views)
Permalink
Re: Problems With additional tuners... [In reply to]
Peter Schneider <peter.schneider [at] schneideris> wrote:

>Hi Andy,
>
>I am thinking that there must in fact be something wrong with either a
>cable or the board for the second connection. All the settings are
>identical between both Video0 and Video1 except for the s-video input
>(1 & 3 respectively) and the audio input (1 & 2 respectively). I
>confirmed the cables, switched sat boxes as a test, and no sound on
>number 2.
>
>I will have to crack open the box next to see if something there is the
>issue. For now though I am going to try and figure out how to
>configure MythTV to work with the HVR-1600 (at the moment it is not
>seeing it so my config is wrong in Myth).
>
>Thanks again for your help and the great education.
>
>-Peter
>
>
>On 2012-02-11, at 7:45 PM, Andy Walls wrote:
>
>> Peter Schneider <peter.schneider [at] schneideris> wrote:
>>
>>> Andy,
>>>
>>> With the second PVR-500 tuner I am not getting any audio. Do you
>have
>>> any idea if this might be related to the v4l2 setup?
>>>
>>> -Peter
>>>
>>> On 2012-02-11, at 4:09 PM, Andy Walls wrote:
>>>
>>>> On Sat, 2012-02-11 at 15:44 -0700, Peter Schneider wrote:
>>>>> Thanks Andy,
>>>>>
>>>>> You are THE MAN!!!! From the v4l2-ctl command I now have the
>analog
>>>>> working on both tuners for the 500 and now on the HVR-1600!!!
>>>>>
>>>>> I am concerned about the HVR-2250 but that will be a debug to
>happen
>>>>> when I have an antenna built. At that time I can use the HVR-1600
>>>>> digital tuner to test the antenna and then engage the HVR-2250.
>>>>>
>>>>> Thanks again Andy.
>>>>
>>>> You're welcome. :)
>>>>
>>>> -Andy
>>>>
>>>>> -Peter
>>>>>
>>>>>
>>>>> On 2012-02-11, at 3:02 PM, Andy Walls wrote:
>>>>>
>>>>>> On Sat, 2012-02-11 at 11:02 -0700, Gmail wrote:
>>>>>>> Hi All,
>>>>
>>>>>>>
>>>>>>> Note: The Analog tuners are being used to capture video through
>>> the
>>>>>>> s-video cable from my satellite tuners and the digital ones are
>>> for
>>>>>>> future OTA HD.
>>>>>>
>>>>>> Please install v4l2-ctl (probably in a v4l2-utils package) and
>>> mplayer.
>>>>>>
>>>>>> Kill the mythbackend, if it is running.
>>>>>>
>>>>>> Then run v4l2-ctl --list-devices, to see what card corresponds to
>>> which
>>>>>> devices nodes. For example:
>>>>>>
>>>>>> $ v4l2-ctl --list-devices
>>>>>> Hauppauge HVR-1600 (PCI:0000:03:00.0):
>>>>>> /dev/video0
>>>>>> /dev/video24
>>>>>> /dev/video32
>>>>>> /dev/vbi0
>>>>>>
>>>>>> Hauppauge WinTV PVR-150 (PCI:0000:03:01.0):
>>>>>> /dev/video2
>>>>>> /dev/video26
>>>>>> /dev/video34
>>>>>> /dev/radio2
>>>>>> /dev/vbi2
>>>>>>
>>>>>> Hauppauge HVR-1600 (PCI:0000:03:02.0):
>>>>>> /dev/video1
>>>>>> /dev/video25
>>>>>> /dev/video33
>>>>>> /dev/radio1
>>>>>> /dev/vbi1
>>>>>>
>>>>>> On a device from which you wish to capture S-Video, set the
>proper
>>> input
>>>>>> and analog TV standard using v4l2-ctl:
>>>>>>
>>>>>> $ v4l2-ctl -d /dev/video0 --list-inputs
>>>>>> ioctl: VIDIOC_ENUMINPUT
>>>>>> Input : 0
>>>>>> Name : Tuner 1
>>>>>> Type : 0x00000001
>>>>>> Audioset : 0x00000007
>>>>>> Tuner : 0x00000000
>>>>>> Standard : 0x0000000000001000 (NTSC-M)
>>>>>> Status : 0x00000000 (ok)
>>>>>> Capabilities: 0x00000004 (SD presets)
>>>>>>
>>>>>> Input : 1
>>>>>> Name : S-Video 1
>>>>>> Type : 0x00000002
>>>>>> Audioset : 0x00000007
>>>>>> Tuner : 0x00000000
>>>>>> Standard : 0x0000000000FFFFFF
>>> (PAL-B/B1/G/H/I/D/D1/K/M/N/Nc/60 NTSC-M/M-JP/443/M-KR
>>> SECAM-B/D/G/H/K/K1/L/Lc)
>>>>>> Status : 0x00000000 (ok)
>>>>>> Capabilities: 0x00000004 (SD presets)
>>>>>>
>>>>>> Input : 2
>>>>>> Name : Composite 1
>>>>>> Type : 0x00000002
>>>>>> Audioset : 0x00000007
>>>>>> Tuner : 0x00000000
>>>>>> Standard : 0x0000000000FFFFFF
>>> (PAL-B/B1/G/H/I/D/D1/K/M/N/Nc/60 NTSC-M/M-JP/443/M-KR
>>> SECAM-B/D/G/H/K/K1/L/Lc)
>>>>>> Status : 0x00000000 (ok)
>>>>>> Capabilities: 0x00000004 (SD presets)
>>>>>> [...]
>>>>>>
>>>>>> $ v4l2-ctl -d /dev/video0 --set-input=1
>>>>>> Video input set to 1 (S-Video 1: ok)
>>>>>>
>>>>>> $ v4l2-ctl -d /dev/video0 --list-standards
>>>>>> ioctl: VIDIOC_ENUMSTD
>>>>>> Index : 0
>>>>>> ID : 0x000000000000B000
>>>>>> Name : NTSC
>>>>>> Frame period: 1001/30000
>>>>>> Frame lines : 525
>>>>>>
>>>>>> Index : 1
>>>>>> ID : 0x0000000000001000
>>>>>> Name : NTSC-M
>>>>>> Frame period: 1001/30000
>>>>>> Frame lines : 525
>>>>>> [...]
>>>>>>
>>>>>> $ v4l2-ctl -d /dev/video0 --set-standard=1
>>>>>> Standard set to 00001000
>>>>>>
>>>>>>
>>>>>> Turn on your S-Video source, and then just capture an MPEG live
>>> with mplayer:
>>>>>>
>>>>>> $ mplayer /dev/video0 -cache 8192
>>>>>>
>>>>>> or capture a file for later playback
>>>>>>
>>>>>> $ cat /dev/video0 > foo.mpg
>>>>>> ^C
>>>>>> $ mplayer foo.mpg
>>>>>>
>>>>>>
>>>>>>
>>>>>>> Here is what I see on the two problematic analog tuners.
>>>>>>
>>>>>> Looks like an untuned tuner input driving the encoder, not
>S-Video.
>>> An
>>>>>> S-Video input that is connected but has no signal is usually a
>>> solid
>>>>>> grey or black screen.
>>>>>>
>>>>
>>>>>> One last step is to verify that you do in fact have a video
>signal
>>> with
>>>>>> a known good devices (such as a TV). If you have RF analog or RF
>>>>>> digital reception problems, you may want to review this checklist
>>> as
>>>>>> well:
>>>>>>
>>>>>> http://ivtvdriver.org/index.php/Howto:Improve_signal_quality
>>>>>>
>>>>>> Regards,
>>>>>> Andy
>>>>>>
>>>>>>>
>>>>>>> -Peter
>>>>
>>>>
>>>>
>>>> _______________________________________________
>>>> ivtv-users mailing list
>>>> ivtv-users [at] ivtvdriver
>>>> http://ivtvdriver.org/mailman/listinfo/ivtv-users
>>>
>>>
>>> _______________________________________________
>>> ivtv-users mailing list
>>> ivtv-users [at] ivtvdriver
>>> http://ivtvdriver.org/mailman/listinfo/ivtv-users
>>
>> No audio for the 2nd RF input means there's a problem with the 2nd
>analog tuner can or a problem with the second CX25843 chip.
>>
>> No audio for the 2nd S Video input usually means you don't have the
>proper extra audio cable/bracket installed. There were at least two
>different versions of that cable/bracket for the 500 and 150 variants.
>>
>> v4l2-ctl -d /dev/videoN --log-status
>>
>> Should tell you what audio input is being used and if the RF
>broadcast audio decoding microcontroller is running or muted. V4l2-ctl
>can also set the audio input explicitly different than the one normally
>paired with a particular video connector.
>>
>> v4l2-ctl --help
>>
>> Lists all the options.
>>
>> -Andy
>>
>> _______________________________________________
>> ivtv-users mailing list
>> ivtv-users [at] ivtvdriver
>> http://ivtvdriver.org/mailman/listinfo/ivtv-users
>
>
>_______________________________________________
>ivtv-users mailing list
>ivtv-users [at] ivtvdriver
>http://ivtvdriver.org/mailman/listinfo/ivtv-users

The HVR-1600 is configured as two video cards in MythTv:
- analog side is an MPEG encoder card like ivtv.
- digital side is a DVB device wih an S5H1409/1411 demodulator.

The analog and digital sides of the 1600 can be used independently and simultaneously, so no need to set up anything special in MythTv.

Regards,
Andy

_______________________________________________
ivtv-users mailing list
ivtv-users [at] ivtvdriver
http://ivtvdriver.org/mailman/listinfo/ivtv-users


peter.schneider at schneideris

Feb 12, 2012, 10:48 AM

Post #9 of 14 (1045 views)
Permalink
Re: Problems With additional tuners... [In reply to]
Thanks Andy,

I have the 1600 showing up now but am trying to track down how to fix a delay/lay of audio. The audio is about a second or two behind the video.

-Peter

On 2012-02-12, at 11:43 AM, Andy Walls wrote:

>
> The HVR-1600 is configured as two video cards in MythTv:
> - analog side is an MPEG encoder card like ivtv.
> - digital side is a DVB device wih an S5H1409/1411 demodulator.
>
> The analog and digital sides of the 1600 can be used independently and simultaneously, so no need to set up anything special in MythTv.
>
> Regards,
> Andy
>
> _______________________________________________
> ivtv-users mailing list
> ivtv-users [at] ivtvdriver
> http://ivtvdriver.org/mailman/listinfo/ivtv-users


_______________________________________________
ivtv-users mailing list
ivtv-users [at] ivtvdriver
http://ivtvdriver.org/mailman/listinfo/ivtv-users


peter.schneider at schneideris

Jun 14, 2012, 3:49 PM

Post #10 of 14 (886 views)
Permalink
Re: Problems With additional tuners... [In reply to]
Hi Andy,

I was hoping you might be able to help me out. I went and did a major package update a couple of days ago (not a version upgrade though) and now there are a couple of problems that are causing me big problems. Initially I could get one of the PVR 500's to work so then I re-installed the v4l2 driver (used git to re-download and build it) and that is what got me to this state.

The first is that what I use v4l2-ctl to "--set-input" and "--set-standard" (I then check and video works) Myth can't access the tuners anymore as they are reporting as busy (myth gives the error that all tuners are busy). The bigger problem is that when I reboot I need to re-run these commands because they get lost (on a cat check to a file the video is missing again).

It also appears that on reboots the dev/video#'s are changing for the different cards. I think this is something that I need to fix with udev based on some of the readings that I have done in the past. Unfortunately I can't say that any of the discussions on udev made a lot of sense to me.

What I want to ask you is if this is something that you have seen before and if so what was the cure that you found?

Here is what the last boot did (actually it has stayed at this organization for three boots now so maybe the driver install caused the re-order). Prior to this one the HVR-1600 had video1 with the PVR 500 split on video0 and video2.

v4l2-ctl --list-devices
Hauppauge HVR-1600 (PCI:0000:01:06.0):
/dev/video0
/dev/video24
/dev/video32
/dev/vbi0

WinTV PVR 500 (unit #1) (PCI:0000:02:08.0):
/dev/video1
/dev/video25
/dev/video33
/dev/radio1
/dev/vbi1

WinTV PVR 500 (unit #2) (PCI:0000:02:09.0):
/dev/video2
/dev/video26
/dev/video34
/dev/vbi2


Thanks,
Peter



On 2012-02-11, at 3:02 PM, Andy Walls wrote:

> On Sat, 2012-02-11 at 11:02 -0700, Gmail wrote:
>> Hi All,
>>
>>
>> I am hoping someone can help me with some trouble shooting that I am
>> doing. I have a box with three Hauppauge cards installed (PVR-500,
>> HVR-2250, and the latest is a HVR 1600). Though I have the 2250
>> installed I have not built my antenna as of yet to bring it online.
>> My PVR-500 used to work with both tuners but then a couple years ago
>> the second unit just stopped working (no idea why and assumed over
>> time, after lots of attempts to try and revive, that it was just
>> dead). I happened across the HVR-1600 yesterday and thought it would
>> make a good addition for the second Analog tuner that I lost. The
>> problem is that it is providing the same static feed as the second
>> tuner from the PVR-500. After looking at the logs I am starting to
>> wonder if the problemI have is a firmware bug or something else and
>> could use some help. The reason I am turning to this list is because
>> of a line in the syslog in what appears to be the ivtv sequence.
>>
>>
>> Note: The Analog tuners are being used to capture video through the
>> s-video cable from my satellite tuners and the digital ones are for
>> future OTA HD.
>
> Please install v4l2-ctl (probably in a v4l2-utils package) and mplayer.
>
> Kill the mythbackend, if it is running.
>
> Then run v4l2-ctl --list-devices, to see what card corresponds to which
> devices nodes. For example:
>
> $ v4l2-ctl --list-devices
> Hauppauge HVR-1600 (PCI:0000:03:00.0):
> /dev/video0
> /dev/video24
> /dev/video32
> /dev/vbi0
>
> Hauppauge WinTV PVR-150 (PCI:0000:03:01.0):
> /dev/video2
> /dev/video26
> /dev/video34
> /dev/radio2
> /dev/vbi2
>
> Hauppauge HVR-1600 (PCI:0000:03:02.0):
> /dev/video1
> /dev/video25
> /dev/video33
> /dev/radio1
> /dev/vbi1
>
> On a device from which you wish to capture S-Video, set the proper input
> and analog TV standard using v4l2-ctl:
>
> $ v4l2-ctl -d /dev/video0 --list-inputs
> ioctl: VIDIOC_ENUMINPUT
> Input : 0
> Name : Tuner 1
> Type : 0x00000001
> Audioset : 0x00000007
> Tuner : 0x00000000
> Standard : 0x0000000000001000 (NTSC-M)
> Status : 0x00000000 (ok)
> Capabilities: 0x00000004 (SD presets)
>
> Input : 1
> Name : S-Video 1
> Type : 0x00000002
> Audioset : 0x00000007
> Tuner : 0x00000000
> Standard : 0x0000000000FFFFFF (PAL-B/B1/G/H/I/D/D1/K/M/N/Nc/60 NTSC-M/M-JP/443/M-KR SECAM-B/D/G/H/K/K1/L/Lc)
> Status : 0x00000000 (ok)
> Capabilities: 0x00000004 (SD presets)
>
> Input : 2
> Name : Composite 1
> Type : 0x00000002
> Audioset : 0x00000007
> Tuner : 0x00000000
> Standard : 0x0000000000FFFFFF (PAL-B/B1/G/H/I/D/D1/K/M/N/Nc/60 NTSC-M/M-JP/443/M-KR SECAM-B/D/G/H/K/K1/L/Lc)
> Status : 0x00000000 (ok)
> Capabilities: 0x00000004 (SD presets)
> [...]
>
> $ v4l2-ctl -d /dev/video0 --set-input=1
> Video input set to 1 (S-Video 1: ok)
>
> $ v4l2-ctl -d /dev/video0 --list-standards
> ioctl: VIDIOC_ENUMSTD
> Index : 0
> ID : 0x000000000000B000
> Name : NTSC
> Frame period: 1001/30000
> Frame lines : 525
>
> Index : 1
> ID : 0x0000000000001000
> Name : NTSC-M
> Frame period: 1001/30000
> Frame lines : 525
> [...]
>
> $ v4l2-ctl -d /dev/video0 --set-standard=1
> Standard set to 00001000
>
>
> Turn on your S-Video source, and then just capture an MPEG live with mplayer:
>
> $ mplayer /dev/video0 -cache 8192
>
> or capture a file for later playback
>
> $ cat /dev/video0 > foo.mpg
> ^C
> $ mplayer foo.mpg
>
>
>
>> Here is what I see on the two problematic analog tuners.
>
> Looks like an untuned tuner input driving the encoder, not S-Video. An
> S-Video input that is connected but has no signal is usually a solid
> grey or black screen.
>
>>
>> Here is some background information:
>
>> and:
>>
>>
>> cat /var/log/syslog|grep cx18
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.465299] cx18: Start initialization, version 1.5.0
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516868] cx18-0: Initializing card 0
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516871] cx18-0: Autodetected Hauppauge card
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.517062] cx18 0000:01:06.0: PCI INT A -> Link[LNKA] -> GSI 16 (level, low) -> IRQ 16
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.523272] cx18-0: cx23418 revision 01010000 (B)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.740991] cx18-0: Autodetected Hauppauge HVR-1600
>
> greping for 'cx18' will miss any error messages reltaed to the tuner
> chips and initialization. Anyway, the HVR-1600 lloks OK from what you
> provided.
>
>>
>> and what set my into this e-mail:
>>
>>
>>
>>
>>
>>
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.371758] Linux video capture interface: v2.00
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.382727] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.449074] ivtv: Start initialization, version 1.4.2
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.453711] parport_pc 00:05: reported by Plug and Play ACPI
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.453762] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.456724] [Firmware Bug]: ACPI(IGPU) defines _DOD but not _DOS
>
> Your computer's BIOS has an ACPI bug that is unrelated to the video
> capture cards, AFAICT.
>
>
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.457016] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:12/LNXVIDEO:00/input/input5
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.457108] ACPI: Video Device [IGPU] (multi-head: yes rom: no post: no)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.458546] ivtv0: Initializing card 0
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.458552] ivtv0: Autodetected Hauppauge card (cx23416 based)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.461226] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 17
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.461251] ivtv 0000:02:08.0: PCI INT A -> Link[LNKB] -> GSI 17 (level, low) -> IRQ 17
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.465299] cx18: Start initialization, version 1.5.0
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516569] tveeprom 2-0050: Hauppauge model 23552, rev E792, serial# 10603908
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516572] tveeprom 2-0050: tuner model is Philips FQ1236A MK4 (idx 92, type 57)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516575] tveeprom 2-0050: TV standards NTSC(M) (eeprom 0x08)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516577] tveeprom 2-0050: second tuner model is Philips TEA5768HL FM Radio (idx 101, type 62)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516580] tveeprom 2-0050: audio processor is CX25843 (idx 37)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516582] tveeprom 2-0050: decoder processor is CX25843 (idx 30)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516584] tveeprom 2-0050: has radio
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516586] ivtv0: Autodetected WinTV PVR 500 (unit #1)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516630] HDA Intel 0000:00:07.0: power state changed by ACPI to D0
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516635] HDA Intel 0000:00:07.0: power state changed by ACPI to D0
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516789] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 21
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516793] HDA Intel 0000:00:07.0: PCI INT A -> Link[LAZA] -> GSI 21 (level, low) -> IRQ 21
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516795] hda_intel: Disabling MSI
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516818] HDA Intel 0000:00:07.0: setting latency timer to 64
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516868] cx18-0: Initializing card 0
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.516871] cx18-0: Autodetected Hauppauge card
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.517047] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 16
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.517062] cx18 0000:01:06.0: PCI INT A -> Link[LNKA] -> GSI 16 (level, low) -> IRQ 16
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.523272] cx18-0: cx23418 revision 01010000 (B)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.527518] cx25840 2-0044: cx25843-24 found @ 0x88 (ivtv i2c driver #0)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.552242] lp0: using parport0 (interrupt-driven).
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.559592] i2c-core: driver [tuner] using legacy suspend method
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.559595] i2c-core: driver [tuner] using legacy resume method
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.571404] tea5767 2-0060: type set to Philips TEA5767HN FM Radio
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.572716] tuner 2-0060: Tuner 62 found with type(s) Radio.
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.647194] tda9887 2-0043: creating new instance
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.647198] tda9887 2-0043: tda988[5/6/7] found
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.648262] tuner 2-0043: Tuner 74 found with type(s) Radio TV.
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.649550] EXT4-fs (sdc1): re-mounted. Opts: errors=remount-ro
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.661166] tuner 2-0061: Tuner -1 found with type(s) TV.
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.661266] MCE: In-kernel MCE decoding enabled.
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.662420] EDAC MC: Ver: 2.1.0
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.667708] AMD64 EDAC driver v3.4.0
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.669263] wm8775 2-001b: chip found @ 0x36 (ivtv i2c driver #0)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.679969] type=1400 audit(1328977336.392:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=765 comm="apparmor_parser"
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.680434] type=1400 audit(1328977336.396:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=765 comm="apparmor_parser"
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.680697] type=1400 audit(1328977336.396:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=765 comm="apparmor_parser"
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.683264] type=1400 audit(1328977336.396:5): apparmor="STATUS" operation="profile_load" name="/usr/sbin/ntpd" pid=786 comm="apparmor_parser"
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.691569] saa7164 driver loaded
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.695133] saa7164 0000:05:00.0: PCI INT A -> Link[LN2A] -> GSI 18 (level, low) -> IRQ 18
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.695958] CORE saa7164[0]: subsystem: 0070:8851, board: Hauppauge WinTV-HVR2250 [card=7,autodetected]
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.695962] saa7164[0]/0: found at 0000:05:00.0, rev: 129, irq: 18, latency: 0, mmio: 0xfe800000
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.695968] saa7164 0000:05:00.0: setting latency timer to 64
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.698088] tuner-simple 2-0061: creating new instance
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.698093] tuner-simple 2-0061: type set to 57 (Philips FQ1236A MK4)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.699764] ivtv0: Registered device video0 for encoder MPG (4096 kB)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.699792] ivtv0: Registered device video32 for encoder YUV (2048 kB)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.699818] ivtv0: Registered device vbi0 for encoder VBI (1024 kB)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.699841] ivtv0: Registered device video24 for encoder PCM (320 kB)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.699866] ivtv0: Registered device radio0 for encoder radio
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.699868] ivtv0: Initialized card: WinTV PVR 500 (unit #1)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.740974] tveeprom 3-0050: Hauppauge model 74041, rev C6G8, serial# 7255283
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.740977] tveeprom 3-0050: MAC address is 00:0d:fe:6e:b4:f3
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.740979] tveeprom 3-0050: tuner model is TCL M30WTP-4N-E (idx 168, type 85)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.740982] tveeprom 3-0050: TV standards NTSC(M) (eeprom 0x08)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.740984] tveeprom 3-0050: audio processor is CX23418 (idx 38)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.740986] tveeprom 3-0050: decoder processor is CX23418 (idx 31)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.740988] tveeprom 3-0050: has no radio, has IR receiver, has IR transmitter
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.740991] cx18-0: Autodetected Hauppauge HVR-1600
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.740993] cx18-0: Simultaneous Digital and Analog TV capture supported
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.748153] ivtv1: Initializing card 1
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.748158] ivtv1: Autodetected Hauppauge card (cx23416 based)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.749970] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 19
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.749978] ivtv 0000:02:09.0: PCI INT A -> Link[LNKC] -> GSI 19 (level, low) -> IRQ 19
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.805055] tveeprom 5-0050: Hauppauge model 23552, rev E792, serial# 10603908
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.805058] tveeprom 5-0050: tuner model is Philips FQ1236A MK4 (idx 92, type 57)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.805060] tveeprom 5-0050: TV standards NTSC(M) (eeprom 0x08)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.805063] tveeprom 5-0050: second tuner model is Philips TEA5768HL FM Radio (idx 101, type 62)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.805065] tveeprom 5-0050: audio processor is CX25843 (idx 37)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.805067] tveeprom 5-0050: decoder processor is CX25843 (idx 30)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.805069] tveeprom 5-0050: has radio
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.805071] ivtv1: Correcting tveeprom data: no radio present on second unit
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.805073] ivtv1: Autodetected WinTV PVR 500 (unit #2)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.811719] cx25840 5-0044: cx25843-24 found @ 0x88 (ivtv i2c driver #1)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.833014] tda9887 5-0043: creating new instance
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.833017] tda9887 5-0043: tda988[5/6/7] found
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.834052] tuner 5-0043: Tuner 74 found with type(s) Radio TV.
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.839893] tuner 5-0061: Tuner -1 found with type(s) Radio TV.
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.845534] wm8775 5-001b: chip found @ 0x36 (ivtv i2c driver #1)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.863936] tuner-simple 5-0061: creating new instance
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.863940] tuner-simple 5-0061: type set to 57 (Philips FQ1236A MK4)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.865665] ivtv1: Registered device video1 for encoder MPG (4096 kB)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.865692] ivtv1: Registered device video33 for encoder YUV (2048 kB)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.865717] ivtv1: Registered device vbi1 for encoder VBI (1024 kB)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.865743] ivtv1: Registered device video25 for encoder PCM (320 kB)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.865745] ivtv1: Initialized card: WinTV PVR 500 (unit #2)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.865799] ivtv: End initialization
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.913467] tda9887 4-0043: creating new instance
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.913470] tda9887 4-0043: tda988[5/6/7] found
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.914339] tuner 4-0043: Tuner 74 found with type(s) Radio TV.
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.920094] tuner 4-0061: Tuner -1 found with type(s) Radio TV.
>
> Every thing appears OK for ivtv and cx18.
>
>
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.944043] saa7164_downloadfirmware() no first image
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.944055] saa7164_downloadfirmware() Waiting for firmware upload (NXP7164-2010-03-10.1.fw)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.964660] JFS: nTxBlock = 8192, nTxLock = 65536
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.982069] cs5345 3-004c: chip found @ 0x98 (cx18 i2c driver #0-0)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.986133] tuner-simple 4-0061: creating new instance
>> Feb 11 09:22:21 mythtv-primary kernel: [ 12.986136] tuner-simple 4-0061: type set to 85 (Philips FQ1236 MK5)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.000831] cx18-0: Registered device video2 for encoder MPEG (64 x 32.00 kB)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.000839] DVB: registering new adapter (cx18)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.001366] ppdev: user-space parallel port driver
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.093375] saa7164_downloadfirmware() Upload failed. (file not found?)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.093380] Failed to boot firmware, no features registered
>
> Your HVR-2250 probably isn't going to work, given those messages about a
> missing firmware file.
>
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.250727] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.510643] EXT4-fs (sdd1): mounted filesystem with ordered data mode. Opts: (null)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.673594] ivtv0: Loaded v4l-cx2341x-enc.fw firmware (376836 bytes)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.701587] ivtv1: Loaded v4l-cx2341x-enc.fw firmware (376836 bytes)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.772527] k8temp 0000:00:18.3: Temperature readouts might be wrong - check erratum #141
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.772807] EDAC amd64: DRAM ECC disabled.
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.772813] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.772814] Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.772815] (Note that use of the override may cause unknown side effects.)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.872180] ivtv0: Encoder revision: 0x02060039
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.883339] MXL5005S: Attached at address 0x63
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.883344] DVB: registering adapter 0 frontend 0 (Samsung S5H1409 QAM/8VSB Frontend)...
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.883461] cx18-0: DVB Frontend registered
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.883464] cx18-0: Registered DVB adapter0 for TS (32 x 32.00 kB)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.883501] cx18-0: Registered device video34 for encoder YUV (20 x 101.25 kB)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.883540] cx18-0: Registered device vbi2 for encoder VBI (20 x 51984 bytes)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.883567] cx18-0: Registered device video26 for encoder PCM audio (256 x 4.00 kB)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.883570] cx18-0: Initialized card: Hauppauge HVR-1600
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.883631] cx18: End initialization
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.900395] ivtv1: Encoder revision: 0x02060039
>> Feb 11 09:22:21 mythtv-primary kernel: [ 13.995615] cx18-alsa: module loading...
>> Feb 11 09:22:21 mythtv-primary kernel: [ 14.162692] cx18-0: loaded v4l-cx23418-cpu.fw firmware (158332 bytes)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 14.413193] cx18-0: loaded v4l-cx23418-apu.fw firmware V00120000 (141200 bytes)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 14.472491] cx18-0: FW version: 0.0.74.0 (Release 2007/03/12)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 15.305943] nvidia: module license 'NVIDIA' taints kernel.
>> Feb 11 09:22:21 mythtv-primary kernel: [ 15.305948] Disabling lock debugging due to kernel taint
>> Feb 11 09:22:21 mythtv-primary kernel: [ 15.543106] ACPI: PCI Interrupt Link [SGRU] enabled at IRQ 20
>> Feb 11 09:22:21 mythtv-primary kernel: [ 15.543114] nvidia 0000:03:00.0: PCI INT A -> Link[SGRU] -> GSI 20 (level, low) -> IRQ 20
>> Feb 11 09:22:21 mythtv-primary kernel: [ 15.543122] nvidia 0000:03:00.0: setting latency timer to 64
>> Feb 11 09:22:21 mythtv-primary kernel: [ 15.543127] vgaarb: device changed decodes: PCI:0000:03:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
>> Feb 11 09:22:21 mythtv-primary kernel: [ 15.544170] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 290.10 Wed Nov 16 17:39:29 PST 2011
>> Feb 11 09:22:21 mythtv-primary kernel: [ 15.738362] cx18-0 843: loaded v4l-cx23418-dig.fw firmware (16382 bytes)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 15.760120] cx18-0 843: verified load of v4l-cx23418-dig.fw firmware (16382 bytes)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 17.589877] cx25840 5-0044: loaded v4l-cx25840.fw firmware (16382 bytes)
>> Feb 11 09:22:21 mythtv-primary kernel: [ 17.899715] RPC: Registered named UNIX socket transport module.
>>
>>
>> Can anyone tell me if I have an actual firmware bug or if this is
>> normal? Can anyone tell me how to test the card for sure to see if it
>> is a defective card?
>
> One last step is to verify that you do in fact have a video signal with
> a known good devices (such as a TV). If you have RF analog or RF
> digital reception problems, you may want to review this checklist as
> well:
>
> http://ivtvdriver.org/index.php/Howto:Improve_signal_quality
>
> Regards,
> Andy
>
>>
>> -Peter
>
>
>
> _______________________________________________
> ivtv-users mailing list
> ivtv-users [at] ivtvdriver
> http://ivtvdriver.org/mailman/listinfo/ivtv-users


peter.schneider at schneideris

Jun 14, 2012, 4:20 PM

Post #11 of 14 (881 views)
Permalink
Re: Problems With additional tuners... [In reply to]
Hi Andy,

I have an update. It appears that this may be a MythTV problem. Specifically one with my MySQL database as suddenly I cannot see any of my prior recordings in the listing anymore and for some strange reason the primary (and only) backend server switched itself to thinking that it is a secondary backend. All in all something very strange has happened and I am going to be beating my head against the wall once again. Doing a cat test after a reboot shows the capture cards are now holding their settings properly but myth still reports them as busy. This though I do suspect is due to a database failure of some sort.

Sorry to have bothered you.

Sincerely,
Peter


peter.schneider at schneideris

Jun 14, 2012, 4:24 PM

Post #12 of 14 (882 views)
Permalink
Re: Problems With additional tuners... [In reply to]
Hi Andy,

I have an update. It appears that this may be a MythTV problem. Specifically one with my MySQL database as suddenly I cannot see any of my prior recordings in the listing anymore and for some strange reason the primary (and only) backend server switched itself to thinking that it is a secondary backend. All in all something very strange has happened and I am going to be beating my head against the wall once again. Doing a cat test after a reboot shows the capture cards are now holding their settings properly but myth still reports them as busy. This though I do suspect is due to a database failure of some sort.

Sorry to have bothered you.

Sincerely,
Peter


awalls at md

Jun 14, 2012, 7:47 PM

Post #13 of 14 (881 views)
Permalink
Re: Problems With additional tuners... [In reply to]
Peter Schneider <peter.schneider [at] schneideris> wrote:

>Hi Andy,
>
>I have an update. It appears that this may be a MythTV problem.
>Specifically one with my MySQL database as suddenly I cannot see any of
>my prior recordings in the listing anymore and for some strange reason
>the primary (and only) backend server switched itself to thinking that
>it is a secondary backend. All in all something very strange has
>happened and I am going to be beating my head against the wall once
>again. Doing a cat test after a reboot shows the capture cards are now
>holding their settings properly but myth still reports them as busy.
>This though I do suspect is due to a database failure of some sort.
>
>Sorry to have bothered you.
>
>Sincerely,
>Peter
>
>_______________________________________________
>ivtv-users mailing list
>ivtv-users [at] ivtvdriver
>http://ivtvdriver.org/mailman/listinfo/ivtv-users

It's no bother. Glad you're on your way to figuring it out.

Regards,
Andy

_______________________________________________
ivtv-users mailing list
ivtv-users [at] ivtvdriver
http://ivtvdriver.org/mailman/listinfo/ivtv-users


peter.schneider at schneideris

Jun 14, 2012, 8:01 PM

Post #14 of 14 (881 views)
Permalink
Re: Problems With additional tuners... [In reply to]
Thanks Andy,

My analysis was right in that the problem turned out to be a DB corruption issue. A nice fellow posted on his blog a repair script that did the trick. Now I just need to figure out why I am getting "video frame buffering failed too many times" after running the live tv for some random period of time.

As a bonus though, the audio sync issue that I was having with the HVR-1600 is fixed.

Sincerely,
Peter




On 2012-06-14, at 8:47 PM, Andy Walls wrote:

> Peter Schneider <peter.schneider [at] schneideris> wrote:
>
>> Hi Andy,
>>
>> I have an update. It appears that this may be a MythTV problem.
>> Specifically one with my MySQL database as suddenly I cannot see any of
>> my prior recordings in the listing anymore and for some strange reason
>> the primary (and only) backend server switched itself to thinking that
>> it is a secondary backend. All in all something very strange has
>> happened and I am going to be beating my head against the wall once
>> again. Doing a cat test after a reboot shows the capture cards are now
>> holding their settings properly but myth still reports them as busy.
>> This though I do suspect is due to a database failure of some sort.
>>
>> Sorry to have bothered you.
>>
>> Sincerely,
>> Peter
>>
>> _______________________________________________
>> ivtv-users mailing list
>> ivtv-users [at] ivtvdriver
>> http://ivtvdriver.org/mailman/listinfo/ivtv-users
>
> It's no bother. Glad you're on your way to figuring it out.
>
> Regards,
> Andy
>
> _______________________________________________
> ivtv-users mailing list
> ivtv-users [at] ivtvdriver
> http://ivtvdriver.org/mailman/listinfo/ivtv-users

ivtv users RSS feed   Index | Next | Previous | View Threaded
 
 


Interested in having your list archived? Contact Gossamer Threads
 
  Web Applications & Managed Hosting Powered by Gossamer Threads Inc.