ivtvlists at littlefish
Nov 5, 2009, 5:41 PM
Post #1 of 1
(79 views)
Permalink
|
I've been using a PVR-250 on an intel DP45SG motherboard with no problems for
quite some time now. Maybe not the latest driver/kernel (CentOS 5.4), but
it's been trouble free and working flawlessly with myth.
Now I've finally gotten around to adding a second PVR-250 that I've been
meaning to get to. The second card is identical to the first card, and it too
has been working just fine in a previous machine.
But I just can't get the two cards to co-exist in the same machine. I can
install each card individually and each works perfectly, but I can't install
them both at the same time.
The machine appeared to be hanging on udev. I thought it might be a udev
thing, so I blacklisted ivtv and the machine completes boot up. But when I
modprobe ivtv, it just locks up solid again. After reviewing the logs it
'looks' like both cards initialize just fine, but after initialization is
complete, the log just ends (which is the point were I power cycle the machine
again).
I should probably start with an updated kernel and driver, but I'm hesitant to
stray outside the CentOS repos. If this is a known problem that can only be
fixed with a version update I guess I'll cross that bridge when I get to it.
Otherwise, I'm open to suggestions.
Here's the ivtv results:
Nov 5 18:43:19 sebastion kernel: Linux video capture interface: v2.00
Nov 5 18:43:19 sebastion kernel: ivtv: ==================== START INIT IVTV
====================
Nov 5 18:43:19 sebastion kernel: ivtv: version 0.10.6 (tagged release) loading
Nov 5 18:43:19 sebastion kernel: ivtv: Linux version: 2.6.18-164.6.1.el5 SMP
mod_unload 686 REGPARM 4KSTACKS gcc-4.1
Nov 5 18:43:19 sebastion kernel: ivtv: In case of problems please include
the debug info between
Nov 5 18:43:19 sebastion kernel: ivtv: the START INIT IVTV and END INIT IVTV
lines, along with
Nov 5 18:43:19 sebastion kernel: ivtv: any module options, when mailing the
ivtv-users mailinglist.
Nov 5 18:43:19 sebastion kernel: ivtv0: Autodetected Hauppauge card (cx23416
based)
Nov 5 18:43:20 sebastion kernel: ivtv0: loaded v4l-cx2341x-enc.fw firmware
(376836 bytes)
Nov 5 18:43:20 sebastion kernel: ivtv0: Retry loading firmware
Nov 5 18:43:21 sebastion kernel: ivtv0: loaded v4l-cx2341x-enc.fw firmware
(376836 bytes)
Nov 5 18:43:21 sebastion kernel: ivtv0: Encoder revision: 0x02060039
Nov 5 18:43:21 sebastion kernel: tveeprom 1-0050: Hauppauge model 32032, rev
B326, serial# 7154586
Nov 5 18:43:21 sebastion kernel: tveeprom 1-0050: tuner model is Temic
4036FY5 (idx 26, type 8)
Nov 5 18:43:21 sebastion kernel: tveeprom 1-0050: TV standards NTSC(M)
(eeprom 0x08)
Nov 5 18:43:21 sebastion kernel: tveeprom 1-0050: audio processor is MSP4448
(idx 27)
Nov 5 18:43:21 sebastion kernel: tveeprom 1-0050: decoder processor is
SAA7115 (idx 19)
Nov 5 18:43:21 sebastion kernel: tveeprom 1-0050: has no radio, has IR remote
Nov 5 18:43:21 sebastion kernel: ivtv0: Autodetected Hauppauge WinTV PVR-250
Nov 5 18:43:21 sebastion kernel: tuner 1-0061: chip found @ 0xc2 (ivtv i2c
driver #0)
Nov 5 18:43:21 sebastion kernel: saa7115 1-0021: saa7115 found @ 0x42 (ivtv
i2c driver #0)
Nov 5 18:43:21 sebastion kernel: msp3400 1-0040: MSP4448G-A2 found @ 0x80
(ivtv i2c driver #0)
Nov 5 18:43:21 sebastion kernel: msp3400 1-0040: MSP4448G-A2 supports radio,
mode is autodetect and autoselect
Nov 5 18:43:21 sebastion kernel: ivtv0: Registered device video0 for encoder
MPEG (4 MB)
Nov 5 18:43:21 sebastion kernel: ivtv0: Registered device video32 for encoder
YUV (2 MB)
Nov 5 18:43:21 sebastion kernel: ivtv0: Registered device vbi0 for encoder
VBI (1 MB)
Nov 5 18:43:21 sebastion kernel: ivtv0: Registered device video24 for encoder
PCM audio (1 MB)
Nov 5 18:43:21 sebastion kernel: tuner 1-0061: type set to 8 (Temic NTSC
(4036 FY5))
Nov 5 18:43:22 sebastion kernel: ivtv0: Initialized Hauppauge WinTV PVR-250,
card #0
Nov 5 18:43:22 sebastion kernel: ivtv: ====================== NEXT CARD
======================
Nov 5 18:43:22 sebastion kernel: ivtv1: Autodetected Hauppauge card (cx23416
based)
Nov 5 18:43:22 sebastion kernel: ivtv1: loaded v4l-cx2341x-enc.fw firmware
(376836 bytes)
Nov 5 18:43:23 sebastion kernel: ivtv1: Encoder revision: 0x02060039
Nov 5 18:43:23 sebastion kernel: tuner 2-0061: chip found @ 0xc2 (ivtv i2c
driver #1)
Nov 5 18:43:23 sebastion kernel: saa7115 2-0021: saa7115 found @ 0x42 (ivtv
i2c driver #1)
Nov 5 18:43:23 sebastion kernel: msp3400 2-0040: MSP4448G-A2 found @ 0x80
(ivtv i2c driver #1)
Nov 5 18:43:23 sebastion kernel: msp3400 2-0040: MSP4448G-A2 supports radio,
mode is autodetect and autoselect
Nov 5 18:43:23 sebastion kernel: tveeprom 2-0050: Hauppauge model 32032, rev
B326, serial# 7154494
Nov 5 18:43:23 sebastion kernel: tveeprom 2-0050: tuner model is Temic
4036FY5 (idx 26, type 8)
Nov 5 18:43:23 sebastion kernel: tveeprom 2-0050: TV standards NTSC(M)
(eeprom 0x08)
Nov 5 18:43:23 sebastion kernel: tveeprom 2-0050: audio processor is MSP4448
(idx 27)
Nov 5 18:43:23 sebastion kernel: tveeprom 2-0050: decoder processor is
SAA7115 (idx 19)
Nov 5 18:43:23 sebastion kernel: tveeprom 2-0050: has no radio, has IR remote
Nov 5 18:43:23 sebastion kernel: ivtv1: Autodetected Hauppauge WinTV PVR-250
Nov 5 18:43:23 sebastion kernel: ivtv1: Registered device video1 for encoder
MPEG (4 MB)
Nov 5 18:43:23 sebastion kernel: ivtv1: Registered device video33 for encoder
YUV (2 MB)
Nov 5 18:43:23 sebastion kernel: ivtv1: Registered device vbi1 for encoder
VBI (1 MB)
Nov 5 18:43:23 sebastion kernel: ivtv1: Registered device video25 for encoder
PCM audio (1 MB)
Nov 5 18:43:23 sebastion kernel: tuner 2-0061: type set to 8 (Temic NTSC
(4036 FY5))
Nov 5 18:43:23 sebastion kernel: ivtv1: Initialized Hauppauge WinTV PVR-250,
card #1
Nov 5 18:43:23 sebastion kernel: ivtv: ==================== END INIT IVTV
====================
Nov 5 18:46:39 sebastion syslogd 1.4.1: restart.
====================
And here's the lspci -vv results
00:00.0 Host bridge: Intel Corporation 4 Series Chipset DRAM Controller (rev 02)
Subsystem: Intel Corporation Unknown device 5001
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00:01.0 PCI bridge: Intel Corporation 4 Series Chipset PCI Express Root Port
(rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: d0000000-e20fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [88] #0d [0000]
Capabilities: [80] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] Message Signalled Interrupts: 64bit- Queue=0/0 Enable+
Address: fee00000 Data: 40c1
Capabilities: [a0] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed unknown, Width x16, ASPM unknown, Port 2
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x16
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
00:19.0 Ethernet controller: Intel Corporation 82567LF-2 Gigabit Network
Connection
Subsystem: Intel Corporation Unknown device 5001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 50
Region 0: Memory at e2100000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at e2124000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at f0e0 [size=32]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable+
Address: 00000000fee01000 Data: 4032
Capabilities: [e0] Vendor Specific Information
00:1a.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI
Controller #4 (prog-if 00 [UHCI])
Subsystem: Intel Corporation Unknown device 5001
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 121
Region 4: I/O ports at f0c0 [size=32]
Capabilities: [50] Vendor Specific Information
00:1a.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI
Controller #5 (prog-if 00 [UHCI])
Subsystem: Intel Corporation Unknown device 5001
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 161
Region 4: I/O ports at f0a0 [size=32]
Capabilities: [50] Vendor Specific Information
00:1a.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI
Controller #6 (prog-if 00 [UHCI])
Subsystem: Intel Corporation Unknown device 5001
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 137
Region 4: I/O ports at f080 [size=32]
Capabilities: [50] Vendor Specific Information
00:1a.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI
Controller #2 (prog-if 20 [EHCI])
Subsystem: Intel Corporation Unknown device 5001
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 137
Region 0: Memory at e2125400 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
Capabilities: [98] Vendor Specific Information
00:1b.0 Audio device: Intel Corporation 82801JI (ICH10 Family) HD Audio Controller
Subsystem: Intel Corporation Unknown device 5001
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 169
Region 0: Memory at e2120000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express Unknown type IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed unknown, Width x0, ASPM unknown, Port 0
Link: Latency L0s <64ns, L1 <1us
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed unknown, Width x0
00:1c.0 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port
1 (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 1
Link: Latency L0s <1us, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x0
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable+
Address: fee00000 Data: 40c9
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1c.1 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port
2 (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: ec200000-ec2fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 2
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable+
Address: fee00000 Data: 40d1
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1d.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI
Controller #1 (prog-if 00 [UHCI])
Subsystem: Intel Corporation Unknown device 5001
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 177
Region 4: I/O ports at f060 [size=32]
Capabilities: [50] Vendor Specific Information
00:1d.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI
Controller #2 (prog-if 00 [UHCI])
Subsystem: Intel Corporation Unknown device 5001
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 145
Region 4: I/O ports at f040 [size=32]
Capabilities: [50] Vendor Specific Information
00:1d.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI
Controller #3 (prog-if 00 [UHCI])
Subsystem: Intel Corporation Unknown device 5001
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 137
Region 4: I/O ports at f020 [size=32]
Capabilities: [50] Vendor Specific Information
00:1d.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI
Controller #1 (prog-if 20 [EHCI])
Subsystem: Intel Corporation Unknown device 5001
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 177
Region 0: Memory at e2125000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
Capabilities: [98] Vendor Specific Information
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 90) (prog-if 01
[Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=64
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: e4000000-ec0fffff
Prefetchable memory behind bridge: 00000000f0000000-00000000f7f00000
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] #0d [0000]
00:1f.0 ISA bridge: Intel Corporation 82801JIR (ICH10R) LPC Interface Controller
Subsystem: Intel Corporation Unknown device 5001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00:1f.2 IDE interface: Intel Corporation 82801JI (ICH10 Family) 4 port SATA
IDE Controller (prog-if 8a [Master SecP PriP])
Subsystem: Intel Corporation Unknown device 5001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 145
Region 0: I/O ports at <ignored>
Region 1: I/O ports at <ignored>
Region 2: I/O ports at <ignored>
Region 3: I/O ports at <ignored>
Region 4: I/O ports at f170 [size=16]
Region 5: I/O ports at f160 [size=16]
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] Vendor Specific Information
00:1f.3 SMBus: Intel Corporation 82801JI (ICH10 Family) SMBus Controller
Subsystem: Intel Corporation Unknown device 5001
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 137
Region 0: Memory at e2125800 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at f000 [size=32]
00:1f.5 IDE interface: Intel Corporation 82801JI (ICH10 Family) 2 port SATA
IDE Controller (prog-if 85 [Master SecO PriO])
Subsystem: Intel Corporation Unknown device 5001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 145
Region 0: I/O ports at f150 [size=8]
Region 1: I/O ports at f140 [size=4]
Region 2: I/O ports at f130 [size=8]
Region 3: I/O ports at f120 [size=4]
Region 4: I/O ports at f110 [size=16]
Region 5: I/O ports at f100 [size=16]
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] Vendor Specific Information
01:00.0 VGA compatible controller: nVidia Corporation G72 [GeForce 7300
SE/7200 GS] (rev a1) (prog-if 00 [VGA controller])
Subsystem: XFX Pine Group Inc. Unknown device 227e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 121
Region 0: Memory at e1000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at e0000000 (64-bit, non-prefetchable) [size=16M]
Expansion ROM at e2000000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [78] Express Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <256ns, L1 <4us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port 0
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 128 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x16
03:00.0 Ethernet controller: Intel Corporation 82572EI Gigabit Ethernet
Controller (Copper) (rev 06)
Subsystem: Intel Corporation PRO/1000 PT Desktop Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 66
Region 0: Memory at ec240000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at ec220000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at e000 [size=32]
Expansion ROM at ec200000 [disabled] [size=128K]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable+
Address: 00000000fee01000 Data: 4042
Capabilities: [e0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <64us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port 0
Link: Latency L0s <4us, L1 <64us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
04:00.0 FireWire (IEEE 1394): Agere Systems FW322/323 (rev 70) (prog-if 10 [OHCI])
Subsystem: Intel Corporation Unknown device 5001
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (3000ns min, 6000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 145
Region 0: Memory at ec001000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
04:02.0 Multimedia video controller: Internext Compression Inc iTVC16
(CX23416) MPEG-2 Encoder (rev 01)
Subsystem: Hauppauge computer works Inc. WinTV PVR 250
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (32000ns min, 2000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 153
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
04:03.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN
interface
Subsystem: Unknown device b1d9:0003
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (250ns min, 32000ns max)
Interrupt: pin A routed to IRQ 161
Region 0: I/O ports at d000 [size=256]
Region 1: Memory at ec000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=55mA PME(D0+,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
04:04.0 Multimedia video controller: Internext Compression Inc iTVC16
(CX23416) MPEG-2 Encoder (rev 01)
Subsystem: Hauppauge computer works Inc. WinTV PVR 250
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (32000ns min, 2000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 169
Region 0: Memory at f4000000 (32-bit, prefetchable) [size=64M]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Scott
--
Registered Linux user #395249, http://counter.li.org
Nothing goes to waste when Little Fish are near!
(http://www.littlefish.ca)
_______________________________________________
ivtv-users mailing list
ivtv-users[at]ivtvdriver.org
http://ivtvdriver.org/mailman/listinfo/ivtv-users
|
