whirly at noos
Oct 22, 2005, 2:04 PM
Post #1 of 1
(312 views)
Permalink
|
|
PVR 150, Black'n'White picture
|
|
Hi,
I am currently trying to run mythtv on the following combination of
software / hardware :
- Biostar 6100 M7 motherboard
(http://www.biostar.com.tw/products/mainboard/board.php?name=GeForce%206100-M7)
- AMD Semptron 2600+
- Hauppauge PVR 150 retail v1052
- GeForce 6200 TC 64
- Guillemot Fortissimo II
- Ubuntu 5.10 Breezy Badger
My source is a Freebox (to make it short, a french tv set top box), I've
got a SCART adaptator from which I get a svideo cable that I connected
to the svideo in of the Hauppauge card.
Everything is working ( cat /dev/video0 grab a nice mpeg, remote control
is working and ir blaster too). Only problem is the video is only black
and white. At first I've tried to use the composite in but there was a
lot of parasite (mostly black and white picture but with some colored
artifact as horizontal colored line). I've tried v0.4.0 then v0.3.8 and
finaly I grab the last 0.4 branch from the SVN but to no avail.
I've searched the net to find a solution it seems that this B&W is quite
recurring (due to wrongly detected card and so on), I tried to force the
card detection and so on, but no cigar.
Thanks,
St?phane
[4294696.247000] ivtv: ==================== START INIT IVTV
====================
[4294696.247000] ivtv: version 0.4.1 (development revision 2842M) loading
[4294696.247000] ivtv: Linux version: 2.6.12-9-386 386 gcc-3.4
[4294696.247000] ivtv: In case of problems please include the debug info
[4294696.247000] ivtv: between the START INIT IVTV and END INIT IVTV
lines when
[4294696.247000] ivtv: mailing the ivtv-devel mailinglist.
[4294696.253000] ivtv0: Autodetected WinTV PVR 150 card (iTVC16 based)
[4294696.254000] ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
[4294696.254000] ACPI: PCI Interrupt 0000:04:08.0[A] -> Link [APC1] ->
GSI 16 (level, low) -> IRQ 16
[4294696.254000] ivtv0: Unreasonably low latency timer, setting to 64
(was 32)
[4294696.316000] tveeprom: ivtv version
[4294696.316000] tveeprom: Hauppauge: model = 26039, rev = C155, serial#
= 2958970
[4294696.316000] tveeprom: tuner = Philips FQ1216ME MK3 (idx = 55, type
= 38)
[4294696.316000] tveeprom: tuner fmt = PAL(B/G) PAL(I) SECAM(L/L')
PAL(D/K) (eeprom = 0x74, v4l2 = 0x00400e17)
[4294696.316000] tveeprom: audio processor = CX25842 (type = 24)
[4294696.316000] tveeprom: decoder processor = CX25842 (type = 1d)
[4294696.316000] ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50]
[4294696.338000] tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c
driver #0
[4294696.338000] ivtv0: i2c attach to card #0 ok [client=(tuner unset),
addr=61]
[4294696.549000] cx25840 0-0044: cx25842-23 found @ 0x88 (ivtv i2c
driver #0)
[4294699.570000] cx25840 0-0044: loaded /lib/modules/HcwMakoA.ROM
firmware (14264 bytes)
[4294699.600000] ivtv0: i2c attach to card #0 ok [client=cx25840, addr=44]
[4294699.617000] wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0)
[4294699.625000] ivtv0: i2c attach to card #0 ok [client=wm8775, addr=1b]
[4294699.655000] tda9885/6/7: (ivtv) chip found @ 0x86
[4294699.655000] ivtv0: i2c attach to card #0 ok [client=tda9887, addr=43]
[4294700.352000] ivtv0: loading /lib/modules/ivtv-fw-enc.bin
[4294700.595000] ivtv0: Encoder revision: 0x02050032check SAA7115 input
signal
[4294700.611000] ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768
buffers (4096KB total)
[4294700.627000] ivtv0: Allocate DMA encoder YUV stream: 161 x 12960
buffers (2048KB total)
[4294700.643000] ivtv0: Allocate DMA encoder VBI stream: 80 x 26208
buffers (2048KB total)
[4294700.658000] ivtv0: Allocate DMA encoder PCM audio stream: 455 x
4608 buffers (2048KB total)
[4294700.659000] tuner: type set to 38 (Philips PAL/SECAM multi
(FM1216ME MK3)) by ivtv i2c driver #0
[4294700.929000] ivtv0: Initialized WinTV PVR 150, card #0
[4294700.929000] ivtv: ==================== END INIT IVTV
====================
ioctl: VIDEO_STATUS = Bad
SAA7115 reg[STATUS#1 - 0x1E] = 00
Color Standard (D0-D1): BW/No color
White peak loop (D2): Not activated
Gain value for act.lum. (min) (D3): Not limited
Gain value for act.lum. (max) (D4): Not limited
WIPA-mode slow-time constant (D5): Not activated
Horizontal frequency (D6): Locked
Field length (D7): Non-standard
SAA7115 reg[STATUS#2 - 0x1F] = 00
Ready for capture (D0): No
Macrovision 7.01 (D1): No
MV Colorstripe burst (D2): No
MV Colorstripe burst type 3 (D3): No
Input signal timebase (D4): Non-stable (VCR)
Field frequency (D5): 50Hz
H & V loops (D6): Locked
Interlace (D7): Not detected
|
