Mailing List Archive: ivtv: devel

PVR 350 (TV-Out) and PVR 150

Index | Next | Previous | View Threaded

nuffersp at yahoo

Jul 25, 2005, 1:35 PM

Post #1 of 15 (2004 views)
Permalink

PVR 350 (TV-Out) and PVR 150

I have scoured both the MythTv and ivtv lists and tried several different options. Unfortunately, none of them have worked. The PVR 350 is in PCI slot #1 and PVR 150 is slot #2.

The PVR 350 is working fine through the TV-Out (Svideo). I receive no apparent messages to indicated where I should go with this. When I use the following command, the file is 0 bytes.

# cat /dev/video1 > /tmp/file

Any suggestions would be greatly appreciated.

** modprobe.conf **
alias char-major-81 videodev
alias char-major-81-0 ivtv
alias char-major-81-1 ivtv
options saa7127 enable_output=1 i2c_enable=1,-1
options ivtv ivtv_debug=1 ivtv_std=1
options cx25840 i2c_enable=1 no_black_magic=1
install ivtv /sbin/modprobe --ignore-install ivtv; /sbin/modprobe ivtv-fb

** ivtv output **
Jul 25 14:46:54 mythback kernel: ivtv: ==================== START INIT IVTV ====================
Jul 25 14:46:54 mythback kernel: ivtv: version 0.3.6 (w) loading
Jul 25 14:46:54 mythback kernel: ivtv: Linux version: 2.6.11-1.35_FC3 686 REGPARM 4KSTACKS gcc-3.4
Jul 25 14:46:54 mythback kernel: ivtv: In case of problems please include the debug info
Jul 25 14:46:54 mythback kernel: ivtv: between the START INIT IVTV and END INIT IVTV lines when
Jul 25 14:46:54 mythback kernel: ivtv: mailing the ivtv-devel mailinglist.
Jul 25 14:46:54 mythback kernel: ivtv: Autodetected WinTV PVR 350 card
Jul 25 14:46:54 mythback kernel: ivtv: Found an iTVC15 based chip
Jul 25 14:46:54 mythback kernel: ivtv: Unreasonably low latency timer, setting to 64 (was 32)
Jul 25 14:46:54 mythback kernel: ivtv: XXX PCI device: 0x01e0 vendor: 0x10de
Jul 25 14:46:54 mythback kernel: ivtv: i2c attach [client=tveeprom[50],ok]
Jul 25 14:46:54 mythback kernel: msp34xx: ivtv version
Jul 25 14:46:54 mythback kernel: ivtv: i2c attach [client=MSP3448W-A2,ok]
Jul 25 14:46:54 mythback kernel: saa7115: starting probe for adapter ivtv i2c driver #0 (0x10005)
Jul 25 14:46:55 mythback kernel: ivtv: i2c attach [client=saa7115[50],ok]
Jul 25 14:46:55 mythback kernel: tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
Jul 25 14:46:55 mythback kernel: ivtv: i2c attach [client=(tuner unset),ok]
Jul 25 14:46:55 mythback kernel: ivtv: i2c attach [client=saa7127[50],ok]
Jul 25 14:46:55 mythback kernel: ivtv: Tuner Type 47, Tuner formats 0x00001000, Radio: yes, Model 0x00ad2598, Revision
0x00000001
Jul 25 14:46:56 mythback kernel: ivtv: NTSC tuner detected
Jul 25 14:46:56 mythback kernel: ivtv: Radio detected
Jul 25 14:46:56 mythback kernel: ivtv: Encoder revision: 0x02040024
Jul 25 14:46:56 mythback kernel: ivtv: Encoder Firmware may be buggy, use version 0x02040011
Jul 25 14:46:56 mythback kernel: ivtv: Decoder revision: 0x02020023
Jul 25 14:46:56 mythback kernel: ivtv: Configuring WinTV PVR 350 card with 10 streams
Jul 25 14:46:56 mythback kernel: ivtv: Registered v4l2 device for encoder MPEG minor 0
Jul 25 14:46:56 mythback kernel: ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total)
Jul 25 14:46:56 mythback kernel: ivtv: Registered v4l2 device for encoder YUV minor 32
Jul 25 14:46:56 mythback kernel: ivtv: Create DMA encoder YUV stream: 0 x 10800 buffers (0KB total)
Jul 25 14:46:56 mythback kernel: ivtv: Registered v4l2 device for encoder VBI minor 224
Jul 25 14:46:56 mythback kernel: ivtv: Create DMA encoder VBI stream: 0 x 8736 buffers (0KB total)
Jul 25 14:46:56 mythback kernel: ivtv: Registered v4l2 device for encoder PCM audio minor 24
Jul 25 14:46:56 mythback kernel: ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total)
Jul 25 14:46:56 mythback kernel: ivtv: Registered v4l2 device for encoder radio minor 64
Jul 25 14:46:56 mythback kernel: ivtv: Create encoder radio stream
Jul 25 14:46:56 mythback kernel: ivtv: Registered v4l2 device for decoder MPEG minor 16
Jul 25 14:46:56 mythback kernel: ivtv: Create DMA decoder MPEG stream: 0 x 65536 buffers (0KB total)
Jul 25 14:46:56 mythback kernel: ivtv: Registered v4l2 device for decoder VBI minor 228
Jul 25 14:46:56 mythback kernel: ivtv: Create DMA decoder VBI stream: 0 x 2048 buffers (0KB total)
Jul 25 14:46:56 mythback kernel: ivtv: Registered v4l2 device for decoder VOUT minor 232
Jul 25 14:46:57 mythback kernel: ivtv: Create decoder VOUT stream
Jul 25 14:46:57 mythback kernel: ivtv: Registered v4l2 device for decoder YUV minor 48
Jul 25 14:46:57 mythback kernel: ivtv: Create DMA decoder YUV stream: 0 x 43200 buffers (0KB total)
Jul 25 14:46:57 mythback kernel: ivtv: Create DMA decoder OSD stream: 0 x 65536 buffers (0KB total)
Jul 25 14:46:57 mythback kernel: ivtv: Setting Tuner 47
Jul 25 14:46:57 mythback kernel: tuner: type set to 47 (LG NTSC (TAPE series)) by ivtv i2c driver #0
Jul 25 14:46:57 mythback kernel: ivtv: ivtv_enc_thread: pid = 585, itv = 0xe0cb29a0
Jul 25 14:46:57 mythback kernel: ivtv: ivtv_enc_vbi_thread: pid = 586, itv = 0xe0cb29a0
Jul 25 14:46:57 mythback kernel: ivtv: ivtv_dec_thread: pid = 587, itv = 0xe0cb29a0
Jul 25 14:46:57 mythback kernel: ivtv: ivtv_dec_vbi_thread: pid = 588, itv = 0xe0cb29a0
Jul 25 14:46:57 mythback kernel: ivtv: Setting audio matrix to input 3, output 1
Jul 25 14:46:57 mythback kernel: ivtv: Switching standard to NTSC.
Jul 25 14:46:57 mythback kernel: ivtv: Initialized WinTV PVR 350, card #0
Jul 25 14:46:57 mythback kernel: ivtv: Autodetected WinTV PVR 150 card
Jul 25 14:46:57 mythback kernel: ivtv: Found an iTVC16 based chip
Jul 25 14:46:57 mythback kernel: ivtv: Unreasonably low latency timer, setting to 64 (was 32)
Jul 25 14:46:57 mythback kernel: ivtv: XXX PCI device: 0x01e0 vendor: 0x10de
Jul 25 14:46:57 mythback kernel: ivtv: i2c attach [client=tveeprom[50],ok]
Jul 25 14:46:57 mythback kernel: saa7115: starting probe for adapter ivtv i2c driver #1 (0x10005)
Jul 25 14:46:57 mythback kernel: tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #1
Jul 25 14:46:57 mythback kernel: ivtv: i2c attach [client=(tuner unset),ok]
Jul 25 14:46:57 mythback kernel: ivtv: i2c attach [client=saa7127[50],ok]
Jul 25 14:46:57 mythback kernel: ivtv: Tuner Type 39, Tuner formats 0x00001000, Radio: yes, Model 0x008d1612, Revision
0x00000000
Jul 25 14:46:57 mythback kernel: ivtv: Radio detected
Jul 25 14:46:57 mythback kernel: ivtv: Encoder revision: 0x02040024
Jul 25 14:46:57 mythback kernel: ivtv: Encoder Firmware may be buggy, use version 0x02040011
Jul 25 14:46:57 mythback kernel: ivtv: Configuring WinTV PVR 150 card with 5 streams
Jul 25 14:46:57 mythback kernel: ivtv: Registered v4l2 device for encoder MPEG minor 1
Jul 25 14:46:57 mythback kernel: ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total)
Jul 25 14:46:57 mythback kernel: ivtv: Registered v4l2 device for encoder YUV minor 33
Jul 25 14:46:57 mythback kernel: ivtv: Create DMA encoder YUV stream: 0 x 10800 buffers (0KB total)
Jul 25 14:46:57 mythback kernel: ivtv: Registered v4l2 device for encoder VBI minor 225
Jul 25 14:46:57 mythback kernel: ivtv: Create DMA encoder VBI stream: 0 x 8736 buffers (0KB total)
Jul 25 14:46:57 mythback kernel: ivtv: Registered v4l2 device for encoder PCM audio minor 25
Jul 25 14:46:57 mythback kernel: ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total)
Jul 25 14:46:57 mythback kernel: ivtv: Registered v4l2 device for encoder radio minor 65
Jul 25 14:46:57 mythback kernel: ivtv: Create encoder radio stream
Jul 25 14:46:57 mythback kernel: ivtv: Setting Tuner 39
Jul 25 14:46:57 mythback kernel: tuner: type set to 39 (LG NTSC (newer TAPC series)) by ivtv i2c driver #1
Jul 25 14:46:57 mythback kernel: ivtv: Switching standard to NTSC.
Jul 25 14:46:57 mythback kernel: ivtv: Initialized WinTV PVR 150, card #1
Jul 25 14:46:57 mythback kernel: ivtv: ==================== END INIT IVTV ====================

Steve
FedoraCore 3
MythTv 18.1

---------------------------------
Start your day with Yahoo! - make it your home page

bmayland at leoninedev

Jul 25, 2005, 2:12 PM

Post #2 of 15 (1974 views)
Permalink

Re: PVR 350 (TV-Out) and PVR 150 [In reply to]

Steve Nuffer wrote:

> ** modprobe.conf **
> alias char-major-81 videodev
> alias char-major-81-0 ivtv
> alias char-major-81-1 ivtv
> options saa7127 enable_output=1 i2c_enable=1,-1
> options ivtv ivtv_debug=1 ivtv_std=1
> options cx25840 i2c_enable=1 no_black_magic=1
> install ivtv /sbin/modprobe --ignore-install ivtv; /sbin/modprobe ivtv-fb
> Jul 25 14:46:55 mythback kernel: ivtv: i2c attach [client=saa7127[50],ok]
> Jul 25 14:46:57 mythback kernel: ivtv: i2c attach [client=saa7127[50],ok]

Looks like the saa7127 module is claiming both cards, and preventing the
cx25840 module from setting up on the PVR150. Your module parameters
look right (i2c_enable=1,-1) though. Can you post a `dmesg | grep
saa7127`?

-------------------------------------------------------
SF.Net email is sponsored by: Discover Easy Linux Migration Strategies
from IBM. Find simple to follow Roadmaps, straightforward articles,
informative Webcasts and more! Get everything you need to get up to
speed, fast. http://ads.osdn.com/?ad_id=7477&alloc_id=16492&op=click
_______________________________________________
ivtv-devel mailing list
ivtv-devel [at] lists
https://lists.sourceforge.net/lists/listinfo/ivtv-devel

reith at racores

Jul 25, 2005, 2:47 PM

Post #3 of 15 (1968 views)
Permalink

Re: PVR 350 (TV-Out) and PVR 150 [In reply to]

>I have scoured both the MythTv and ivtv lists and tried several
>different options. Unfortunately, none of them have worked. The
>PVR 350 is in PCI slot #1 and PVR 150 is slot #2.
>
>The PVR 350 is working fine through the TV-Out (Svideo). I receive
>no apparent messages to indicated where I should go with this. When
>I use the following command, the file is 0 bytes.
>
># cat /dev/video1 > /tmp/file
>
>Any suggestions would be greatly appreciated.
>
>** modprobe.conf **
>alias char-major-81 videodev
>alias char-major-81-0 ivtv
>alias char-major-81-1 ivtv
>options saa7127 enable_output=1 i2c_enable=1,-1
>options ivtv ivtv_debug=1 ivtv_std=1
>options cx25840 i2c_enable=1 no_black_magic=1
>install ivtv /sbin/modprobe --ignore-install ivtv; /sbin/modprobe ivtv-fb

remove the black magic line and set the cx25840 i2c options to the
opposite of the saa7127

options cx25840 i2c_enable=-1,1

>
>** ivtv output **
>Jul 25 14:46:54 mythback kernel: ivtv: ==================== START
>INIT IVTV ====================
>Jul 25 14:46:54 mythback kernel: ivtv: version 0.3.6 (w) loading
>Jul 25 14:46:54 mythback kernel: ivtv: Linux version:
>2.6.11-1.35_FC3 686 REGPARM 4KSTACKS gcc-3.4
>Jul 25 14:46:54 mythback kernel: ivtv: In case of problems please
>include the debug info
>Jul 25 14:46:54 mythback kernel: ivtv: between the START INIT IVTV
>and END INIT IVTV lines when
>Jul 25 14:46:54 mythback kernel: ivtv: mailing the ivtv-devel mailinglist.
>Jul 25 14:46:54 mythback kernel: ivtv: Autodetected WinTV PVR 350 card
>Jul 25 14:46:54 mythback kernel: ivtv: Found an iTVC15 based chip
>Jul 25 14:46:54 mythback kernel: ivtv: Unreasonably low latency
>timer, setting to 64 (was 32)
>Jul 25 14:46:54 mythback kernel: ivtv: XXX PCI device: 0x01e0 vendor: 0x10de
>Jul 25 14:46:54 mythback kernel: ivtv: i2c attach [client=tveeprom[50],ok]
>Jul 25 14:46:54 mythback kernel: msp34xx: ivtv version
>Jul 25 14:46:54 mythback kernel: ivtv: i2c attach [client=MSP3448W-A2,ok]
>Jul 25 14:46:54 mythback kernel: saa7115: starting probe for adapter
>ivtv i2c driver #0 (0x10005)
>Jul 25 14:46:55 mythback kernel: ivtv: i2c attach [client=saa7115[50],ok]
>Jul 25 14:46:55 mythback kernel: tuner: chip found at addr 0xc2
>i2c-bus ivtv i2c driver #0
>Jul 25 14:46:55 mythback kernel: ivtv: i2c attach [client=(tuner unset),ok]
>Jul 25 14:46:55 mythback kernel: ivtv: i2c attach [client=saa7127[50],ok]
>Jul 25 14:46:55 mythback kernel: ivtv: Tuner Type 47, Tuner formats
>0x00001000, Radio: yes, Model 0x00ad2598, Revision
>0x00000001
>Jul 25 14:46:56 mythback kernel: ivtv: NTSC tuner detected
>Jul 25 14:46:56 mythback kernel: ivtv: Radio detected
>Jul 25 14:46:56 mythback kernel: ivtv: Encoder revision: 0x02040024
>Jul 25 14:46:56 mythback kernel: ivtv: Encoder Firmware may be
>buggy, use version 0x02040011
>Jul 25 14:46:56 mythback kernel: ivtv: Decoder rev ision: 0x02020023
>Jul 25 14:46:56 mythback kernel: ivtv: Configuring WinTV PVR 350
>card with 10 streams
>Jul 25 14:46:56 mythback kernel: ivtv: Registered v4l2 device for
>encoder MPEG minor 0
>Jul 25 14:46:56 mythback kernel: ivtv: Create DMA encoder MPEG
>stream: 0 x 32768 buffers (0KB total)
>Jul 25 14:46:56 mythback kernel: ivtv: Registered v4l2 device for
>encoder YUV minor 32
>Jul 25 14:46:56 mythback kernel: ivtv: Create DMA encoder YUV
>stream: 0 x 10800 buffers (0KB total)
>Jul 25 14:46:56 mythback kernel: ivtv: Registered v4l2 device for
>encoder VBI minor 224
>Jul 25 14:46:56 mythback kernel: ivtv: Create DMA encoder VBI
>stream: 0 x 8736 buffers (0KB total)
>Jul 25 14:46:56 mythback kernel: ivtv: Registered v4l2 device for
>encoder PCMaudio minor 24
>Jul 25 14:46:56 mythback kernel: ivtv: Create DMA encoder PCM audio
>stream: 0 x 4608 buffers (0KB total)
>Jul 25 14:46:56 mythback kernel: ivtv: Registered v4l2 device for
>encoder radio minor 64
>Jul 25 14: 46:56 mythback kernel: ivtv: Create encoder radio stream
>Jul 25 14:46:56 mythback kernel: ivtv: Registered v4l2 device for
>decoder MPEG minor 16
>Jul 25 14:46:56 mythback kernel: ivtv: Create DMA decoder MPEG
>stream: 0 x 65536 buffers (0KB total)
>Jul 25 14:46:56 mythback kernel: ivtv: Registered v4l2 device for
>decoder VBI minor 228
>Jul 25 14:46:56 mythback kernel: ivtv: Create DMA decoder VBI
>stream: 0 x 2048 buffers (0KB total)
>Jul 25 14:46:56 mythback kernel: ivtv: Registered v4l2 device for
>decoder VOUT minor 232
>Jul 25 14:46:57 mythback kernel: ivtv: Create decoder VOUT stream
>Jul 25 14:46:57 mythback kernel: ivtv: Registered v4l2 device for
>decoder YUV minor 48
>Jul 25 14:46:57 mythback kernel: ivtv: Create DMA decoder YUV
>stream: 0 x 43200 buffers (0KB total)
>Jul 25 14:46:57 mythback kernel: ivtv: Create DMA decoder OSD
>stream: 0 x 65536 buffers (0KB total)
>Jul 25 14:46:57 mythback kernel: ivtv: Setting Tuner 47
>Jul 25 14:46:57 mythback kernel : tuner: type set to 47 (LG NTSC
>(TAPE series)) by ivtv i2c driver #0
>Jul 25 14:46:57 mythback kernel: ivtv: ivtv_enc_thread: pid = 585,
>itv = 0xe0cb29a0
>Jul 25 14:46:57 mythback kernel: ivtv: ivtv_enc_vbi_thread: pid =
>586, itv = 0xe0cb29a0
>Jul 25 14:46:57 mythback kernel: ivtv: ivtv_dec_thread: pid = 587,
>itv = 0xe0cb29a0
>Jul 25 14:46:57 mythback kernel: ivtv: ivtv_dec_vbi_thread: pid =
>588, itv = 0xe0cb29a0
>Jul 25 14:46:57 mythback kernel: ivtv: Setting audio matrix to input
>3, output 1
>Jul 25 14:46:57 mythback kernel: ivtv: Switching standard to NTSC.
>Jul 25 14:46:57 mythback kernel: ivtv: Initialized WinTV PVR 350, card #0
>Jul 25 14:46:57 mythback kernel: ivtv: Autodetected WinTV PVR 150 card
>Jul 25 14:46:57 mythback kernel: ivtv: Found an iTVC16 based chip
>Jul 25 14:46:57 mythback kernel: ivtv: Unreasonably low latency
>timer, setting to 64 (was 32)
>Jul 25 14:46:57 mythback kernel: ivtv: XXX PCI device: 0x01e0 vendor: 0x10de
>Jul 25 14:46:57 my thback kernel: ivtv: i2c attach [client=tveeprom[50],ok]
>Jul 25 14:46:57 mythback kernel: saa7115: starting probe for adapter
>ivtv i2c driver #1 (0x10005)
>Jul 25 14:46:57 mythback kernel: tuner: chip found at addr 0xc2
>i2c-bus ivtv i2c driver #1
>Jul 25 14:46:57 mythback kernel: ivtv: i2c attach [client=(tuner unset),ok]
>Jul 25 14:46:57 mythback kernel: ivtv: i2c attach [client=saa7127[50],ok]
>Jul 25 14:46:57 mythback kernel: ivtv: Tuner Type 39, Tuner formats
>0x00001000, Radio: yes, Model 0x008d1612, Revision
>0x00000000
>Jul 25 14:46:57 mythback kernel: ivtv: Radio detected
>Jul 25 14:46:57 mythback kernel: ivtv: Encoder revision: 0x02040024
>Jul 25 14:46:57 mythback kernel: ivtv: Encoder Firmware may be
>buggy, use version 0x02040011
>Jul 25 14:46:57 mythback kernel: ivtv: Configuring WinTV PVR 150
>card with 5 streams
>Jul 25 14:46:57 mythback kernel: ivtv: Registered v4l2 device for
>encoder MPEG minor 1
>Jul 25 14:46:57 mythback kernel: ivtv: Create DMA encoder MPEG
>stream: 0 x 32768 buffers (0KB total)
>Jul 25 14:46:57 mythback kernel: ivtv: Registered v4l2 device for
>encoder YUV minor 33
>Jul 25 14:46:57 mythback kernel: ivtv: Create DMA encoder YUV
>stream: 0 x 10800 buffers (0KB total)
>Jul 25 14:46:57 mythback kernel: ivtv: Registered v4l2 device for
>encoder VBI minor 225
>Jul 25 14:46:57 mythback kernel: ivtv: Create DMA encoder VBI
>stream: 0 x 8736 buffers (0KB total)
>Jul 25 14:46:57 mythback kernel: ivtv: Registered v4l2 device for
>encoder PCM audio minor 25
>Jul 25 14:46:57 mythback kernel: ivtv: Create DMA encoder PCM audio
>stream: 0 x 4608 buffers (0KB total)
>Jul 25 14:46:57 mythback kernel: ivtv: Registered v4l2 device for
>encoder radio minor 65
>Jul 25 14:46:57 mythback kernel: ivtv: Create encoder radio stream
>Jul 25 14:46:57 mythback kernel: ivtv: Setting Tuner 39
>Jul 25 14:46:57 mythback kernel: tuner: type set to 39 (LG NTSC
>(newer TAPC series)) by ivtv i2c driver #1
>Jul 25 14:46:5 7 mythback kernel: ivtv: Switching standard to NTSC.
>Jul 25 14:46:57 mythback kernel: ivtv: Initialized WinTV PVR 150, card #1
>Jul 25 14:46:57 mythback kernel: ivtv: ==================== END
>INIT IVTV ====================
>
>Steve
>FedoraCore 3
>MythTv 18.1
>
>
>
><http://us.rd.yahoo.com/evt=34442/*http://www.yahoo.com/r/hs>Start
>your day with Yahoo! - make it your home page

bmayland at leoninedev

Jul 25, 2005, 4:08 PM

Post #4 of 15 (1961 views)
Permalink

Re: PVR 350 (TV-Out) and PVR 150 [In reply to]

Jim Reith wrote:

> remove the black magic line and set the cx25840 i2c options to the
> opposite of the saa7127
> options cx25840 i2c_enable=-1,1

Actually since like version 0.3.6m, it is better not to set this
option at all (since the cx25840 can be actually probed properly, unlike
the saa7127). In fact, in the version he posted the log from 0.3.6w
will actually disable the cx25840 on the PVR150 (since it is before the
i2c_enable sanity patch in 0.3.7)

So long story short, don't put any module parameters on the cx25840.
But still post the dmesg | grep saa7127 please.

-------------------------------------------------------
SF.Net email is sponsored by: Discover Easy Linux Migration Strategies
from IBM. Find simple to follow Roadmaps, straightforward articles,
informative Webcasts and more! Get everything you need to get up to
speed, fast. http://ads.osdn.com/?ad_id=7477&alloc_id=16492&op=click
_______________________________________________
ivtv-devel mailing list
ivtv-devel [at] lists
https://lists.sourceforge.net/lists/listinfo/ivtv-devel

nuffersp at yahoo

Jul 25, 2005, 4:30 PM

Post #5 of 15 (1972 views)
Permalink

Re: PVR 350 (TV-Out) and PVR 150 [In reply to]

I changed the modprobe.conf to the following with the same results.

** modprobe.conf **
alias char-major-81 videodev
alias char-major-81-0 ivtv
alias char-major-81-1 ivtv
options saa7127 enable_output=1 i2c_enable=1,-1
options ivtv ivtv_debug=1 ivtv_std=1
options cx25840 i2c_enable=-1,1
install ivtv /sbin/modprobe --ignore-install ivtv; /sbin/modprobe ivtv-fb

** dmesg | grep ivtv ** ( the output was too large for the list )
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.3.6 (w) loading
ivtv: Linux version: 2.6.11-1.35_FC3 686 REGPARM 4KSTACKS gcc-3.4
ivtv: In case of problems please include the debug info
ivtv: between the START INIT IVTV and END INIT IVTV lines when
ivtv: mailing the ivtv-devel mailinglist.
ivtv: Autodetected WinTV PVR 350 card
ivtv: Found an iTVC15 based chip
ivtv: Unreasonably low latency timer, setting to 64 (was 32)
ivtv: XXX PCI device: 0x01e0 vendor: 0x10de
ivtv: i2c attach [client=tveeprom[50],ok]
msp34xx: ivtv version
ivtv: i2c attach [client=MSP3448W-A2,ok]
saa7115: starting probe for adapter ivtv i2c driver #0 (0x10005)
ivtv: i2c attach [client=saa7115[50],ok]
tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
ivtv: i2c attach [client=(tuner unset),ok]
ivtv: i2c attach [client=saa7127[50],ok]
ivtv: Tuner Type 47, Tuner formats 0x00001000, Radio: yes, Model 0x00ad2598, Revision 0x00000001
ivtv: NTSC tuner detected
ivtv: Radio detected
ivtv: Encoder revision: 0x02040024
ivtv: Encoder Firmware may be buggy, use version 0x02040011
ivtv: Decoder revision: 0x02020023
ivtv: Configuring WinTV PVR 350 card with 10 streams
ivtv: Registered v4l2 device for encoder MPEG minor 0
ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total)
ivtv: Registered v4l2 device for encoder YUV minor 32
ivtv: Create DMA encoder YUV stream: 0 x 10800 buffers (0KB total)
ivtv: Registered v4l2 device for encoder VBI minor 224
ivtv: Create DMA encoder VBI stream: 0 x 8736 buffers (0KB total)
ivtv: Registered v4l2 device for encoder PCM audio minor 24
ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total)
ivtv: Registered v4l2 device for encoder radio minor 64
ivtv: Create encoder radio stream
ivtv: Registered v4l2 device for decoder MPEG minor 16
ivtv: Create DMA decoder MPEG stream: 0 x 65536 buffers (0KB total)
ivtv: Registered v4l2 device for decoder VBI minor 228
ivtv: Create DMA decoder VBI stream: 0 x 2048 buffers (0KB total)
ivtv: Registered v4l2 device for decoder VOUT minor 232
ivtv: Create decoder VOUT stream
ivtv: Registered v4l2 device for decoder YUV minor 48
ivtv: Create DMA decoder YUV stream: 0 x 43200 buffers (0KB total)
ivtv: Create DMA decoder OSD stream: 0 x 65536 buffers (0KB total)
ivtv: Setting Tuner 47
tuner: type set to 47 (LG NTSC (TAPE series)) by ivtv i2c driver #0
ivtv: ivtv_enc_thread: pid = 585, itv = 0xe0cb29a0
ivtv: ivtv_enc_vbi_thread: pid = 586, itv = 0xe0cb29a0
ivtv: ivtv_dec_thread: pid = 587, itv = 0xe0cb29a0
ivtv: ivtv_dec_vbi_thread: pid = 588, itv = 0xe0cb29a0
ivtv: Setting audio matrix to input 3, output 1
ivtv: Switching standard to NTSC.
ivtv: Initialized WinTV PVR 350, card #0
ivtv: Autodetected WinTV PVR 150 card
ivtv: Found an iTVC16 based chip
ivtv: Unreasonably low latency timer, setting to 64 (was 32)
ivtv: XXX PCI device: 0x01e0 vendor: 0x10de
ivtv: i2c attach [client=tveeprom[50],ok]
saa7115: starting probe for adapter ivtv i2c driver #1 (0x10005)
tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #1
ivtv: i2c attach [client=(tuner unset),ok]
ivtv: i2c attach [client=saa7127[50],ok]
ivtv: Tuner Type 39, Tuner formats 0x00001000, Radio: yes, Model 0x008d1612, Revision 0x00000000
ivtv: Radio detected
ivtv: Encoder revision: 0x02040024
ivtv: Encoder Firmware may be buggy, use version 0x02040011
ivtv: Configuring WinTV PVR 150 card with 5 streams
ivtv: Registered v4l2 device for encoder MPEG minor 1
ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total)
ivtv: Registered v4l2 device for encoder YUV minor 33
ivtv: Create DMA encoder YUV stream: 0 x 10800 buffers (0KB total)
ivtv: Registered v4l2 device for encoder VBI minor 225
ivtv: Create DMA encoder VBI stream: 0 x 8736 buffers (0KB total)
ivtv: Registered v4l2 device for encoder PCM audio minor 25
ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total)
ivtv: Registered v4l2 device for encoder radio minor 65
ivtv: Create encoder radio stream
ivtv: Setting Tuner 39
tuner: type set to 39 (LG NTSC (newer TAPC series)) by ivtv i2c driver #1
ivtv: Switching standard to NTSC.
ivtv: Initialized WinTV PVR 150, card #1
ivtv: ==================== END INIT IVTV ====================
ivtv: ivtv_enc_thread: pid = 608, itv = 0xe0cd5f54
ivtv: ivtv_enc_vbi_thread: pid = 609, itv = 0xe0cd5f54
ivtv-osd: Framebuffer module loaded (attached to ivtv card id 0)
ivtv-osd: Framebuffer is at decoder-relative address 0x00510000 and has 1704960 bytes.
ivtv-osd: screen coords: [0 0] -> [720 480]
ivtv-osd: original global alpha = 208
ivtv-osd: current OSD state = 39
ivtv-osd: new global alpha = 208 (1 255 0)
ivtv-osd: framebuffer at 0xe1510000, mapped to 0xe1b90000, size 1350k
ivtv-osd: mode is 720x480x32, linelength=2880
ivtv-osd: fb1: iTVC15 TV out frame buffer device
ivtv: Allocate DMA decoder OSD stream: 16 x 65536 buffers (1024KB total)
ivtv: i2c attach [client=Hauppauge IR,ok]
ivtv: i2c attach [client=Hauppauge IR (PVR150),ok]
ivtv: Tried to open YUV output device but need to send data to mpeg decoder before it can be used
ivtv: Tried to open YUV output device but need to send data to mpeg decoder before it can be used
ivtv: Tried to open YUV output device but need to send data to mpeg decoder before it can be used
ivtv: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv: Setup VBI API header 0x0000bd0d pkts 1 buffs 4 ln 24 sz 1456
ivtv: Setup VBI start 0x0018ea04 frames 4 fpi 1 lines 0x00000140

__________________________________________________
Do You Yahoo!?
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com

nuffersp at yahoo

Jul 25, 2005, 7:14 PM

Post #6 of 15 (1967 views)
Permalink

Re: PVR 350 (TV-Out) and PVR 150 [In reply to]

Thanks for giving some suggestions. There was no change in the size, zero, in the command, "cat /dev/video1 >/tmp/filea'.

** /etc/modprobe.confmp **
alias char-major-81 videodev
alias char-major-81-0 ivtv
alias char-major-81-1 ivtv
options saa7127 enable_output=1 i2c_enable=1,-1
options ivtv ivtv_debug=1 ivtv_std=1

** ivtv output **
Jul 25 21:06:57 mythback kernel: ivtv: ==================== START INIT IVTV ====================
Jul 25 21:06:57 mythback kernel: ivtv: version 0.3.6 (w) loading
Jul 25 21:06:57 mythback kernel: ivtv: Linux version: 2.6.11-1.35_FC3 686 REGPARM 4KSTACKS gcc-3.4
Jul 25 21:06:57 mythback kernel: ivtv: In case of problems please include the debug info
Jul 25 21:06:57 mythback kernel: ivtv: between the START INIT IVTV and END INIT IVTV lines when
Jul 25 21:06:57 mythback kernel: ivtv: mailing the ivtv-devel mailinglist.
Jul 25 21:06:57 mythback kernel: ivtv: Autodetected WinTV PVR 350 card
Jul 25 21:06:57 mythback kernel: ivtv: Found an iTVC15 based chip
Jul 25 21:06:57 mythback kernel: ivtv: Unreasonably low latency timer, setting to 64 (was 32)
Jul 25 21:06:57 mythback kernel: ivtv: XXX PCI device: 0x01e0 vendor: 0x10de
Jul 25 21:06:57 mythback kernel: ivtv: i2c attach [client=tveeprom[50],ok]
Jul 25 21:06:57 mythback kernel: msp34xx: ivtv version
Jul 25 21:06:57 mythback kernel: ivtv: i2c attach [client=MSP3448W-A2,ok]
Jul 25 21:06:57 mythback kernel: saa7115: starting probe for adapter ivtv i2c driver #0 (0x10005)
Jul 25 21:06:57 mythback kernel: ivtv: i2c attach [client=saa7115[50],ok]
Jul 25 21:06:57 mythback kernel: tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
Jul 25 21:06:57 mythback kernel: ivtv: i2c attach [client=(tuner unset),ok]
Jul 25 21:06:57 mythback kernel: ivtv: i2c attach [client=saa7127[50],ok]
Jul 25 21:06:57 mythback kernel: ivtv: Tuner Type 47, Tuner formats 0x00001000, Radio: yes, Model 0x00ad2598, Revision 0x00000001
Jul 25 21:06:57 mythback kernel: ivtv: NTSC tuner detected
Jul 25 21:06:57 mythback kernel: ivtv: Radio detected
Jul 25 21:06:57 mythback kernel: ivtv: Encoder revision: 0x02040024
Jul 25 21:06:57 mythback kernel: ivtv: Encoder Firmware may be buggy, use version 0x02040011
Jul 25 21:06:57 mythback kernel: ivtv: Decoder revision: 0x02020023
Jul 25 21:06:58 mythback kernel: ivtv: Configuring WinTV PVR 350 card with 10 streams
Jul 25 21:06:58 mythback kernel: ivtv: Registered v4l2 device for encoder MPEG minor 0
Jul 25 21:06:58 mythback kernel: ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total)
Jul 25 21:06:58 mythback kernel: ivtv: Registered v4l2 device for encoder YUV minor 32
Jul 25 21:06:58 mythback kernel: ivtv: Create DMA encoder YUV stream: 0 x 10800 buffers (0KB total)
Jul 25 21:06:58 mythback kernel: ivtv: Registered v4l2 device for encoder VBI minor 224
Jul 25 21:06:58 mythback kernel: ivtv: Create DMA encoder VBI stream: 0 x 8736 buffers (0KB total)
Jul 25 21:06:58 mythback kernel: ivtv: Registered v4l2 device for encoder PCM audio minor 24
Jul 25 21:06:59 mythback kernel: ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total)
Jul 25 21:06:59 mythback kernel: ivtv: Registered v4l2 device for encoder radio minor 64
Jul 25 21:06:59 mythback kernel: ivtv: Create encoder radio stream
Jul 25 21:06:59 mythback kernel: ivtv: Registered v4l2 device for decoder MPEG minor 16
Jul 25 21:06:59 mythback kernel: ivtv: Create DMA decoder MPEG stream: 0 x 65536 buffers (0KB total)
Jul 25 21:06:59 mythback kernel: ivtv: Registered v4l2 device for decoder VBI minor 228
Jul 25 21:06:59 mythback kernel: ivtv: Create DMA decoder VBI stream: 0 x 2048 buffers (0KB total)
Jul 25 21:06:59 mythback kernel: ivtv: Registered v4l2 device for decoder VOUT minor 232
Jul 25 21:06:59 mythback kernel: ivtv: Create decoder VOUT stream
Jul 25 21:06:59 mythback kernel: ivtv: Registered v4l2 device for decoder YUV minor 48
Jul 25 21:06:59 mythback kernel: ivtv: Create DMA decoder YUV stream: 0 x 43200 buffers (0KB total)
Jul 25 21:06:59 mythback kernel: ivtv: Create DMA decoder OSD stream: 0 x 65536 buffers (0KB total)
Jul 25 21:06:59 mythback kernel: ivtv: Setting Tuner 47
Jul 25 21:06:59 mythback kernel: tuner: type set to 47 (LG NTSC (TAPE series)) by ivtv i2c driver #0
Jul 25 21:06:59 mythback kernel: ivtv: Setting audio matrix to input 3, output 1
Jul 25 21:06:59 mythback kernel: ivtv: Switching standard to NTSC.
Jul 25 21:06:59 mythback kernel: ivtv: ivtv_enc_thread: pid = 585, itv = 0xe0cb29a0
Jul 25 21:06:59 mythback kernel: ivtv: ivtv_enc_vbi_thread: pid = 586, itv = 0xe0cb29a0
Jul 25 21:07:00 mythback kernel: ivtv: ivtv_dec_thread: pid = 587, itv = 0xe0cb29a0
Jul 25 21:07:00 mythback kernel: ivtv: ivtv_dec_vbi_thread: pid = 588, itv = 0xe0cb29a0
Jul 25 21:07:00 mythback kernel: ivtv: Initialized WinTV PVR 350, card #0
Jul 25 21:07:00 mythback kernel: ivtv: Autodetected WinTV PVR 150 card
Jul 25 21:07:00 mythback kernel: ivtv: Found an iTVC16 based chip
Jul 25 21:07:00 mythback kernel: ivtv: Unreasonably low latency timer, setting to 64 (was 32)
Jul 25 21:07:00 mythback kernel: ivtv: XXX PCI device: 0x01e0 vendor: 0x10de
Jul 25 21:07:00 mythback kernel: ivtv: i2c attach [client=tveeprom[50],ok]
Jul 25 21:07:00 mythback kernel: saa7115: starting probe for adapter ivtv i2c driver #1 (0x10005)
Jul 25 21:07:00 mythback kernel: tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #1
Jul 25 21:07:00 mythback kernel: ivtv: i2c attach [client=(tuner unset),ok]
Jul 25 21:07:00 mythback kernel: ivtv: i2c attach [client=saa7127[50],ok]
Jul 25 21:07:00 mythback kernel: ivtv: Tuner Type 39, Tuner formats 0x00001000, Radio: yes, Model 0x008d1612, Revision 0x00000000
Jul 25 21:07:00 mythback kernel: ivtv: Radio detected
Jul 25 21:07:00 mythback kernel: ivtv: Encoder revision: 0x02040024
Jul 25 21:07:00 mythback kernel: ivtv: Encoder Firmware may be buggy, use version 0x02040011
Jul 25 21:07:00 mythback kernel: ivtv: Configuring WinTV PVR 150 card with 5 streams
Jul 25 21:07:00 mythback kernel: ivtv: Registered v4l2 device for encoder MPEG minor 1
Jul 25 21:07:00 mythback kernel: ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total)
Jul 25 21:07:00 mythback kernel: ivtv: Registered v4l2 device for encoder YUV minor 33
Jul 25 21:07:00 mythback kernel: ivtv: Create DMA encoder YUV stream: 0 x 10800 buffers (0KB total)
Jul 25 21:07:00 mythback kernel: ivtv: Registered v4l2 device for encoder VBI minor 225
Jul 25 21:07:00 mythback kernel: ivtv: Create DMA encoder VBI stream: 0 x 8736 buffers (0KB total)
Jul 25 21:07:00 mythback kernel: ivtv: Registered v4l2 device for encoder PCM audio minor 25
Jul 25 21:07:00 mythback kernel: ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total)
Jul 25 21:07:00 mythback kernel: ivtv: Registered v4l2 device for encoder radio minor 65
Jul 25 21:07:00 mythback kernel: ivtv: Create encoder radio stream
Jul 25 21:07:00 mythback kernel: ivtv: Setting Tuner 39
Jul 25 21:07:00 mythback kernel: tuner: type set to 39 (LG NTSC (newer TAPC series)) by ivtv i2c driver #1
Jul 25 21:07:00 mythback kernel: ivtv: Switching standard to NTSC.
Jul 25 21:07:00 mythback kernel: ivtv: Initialized WinTV PVR 150, card #1
Jul 25 21:07:00 mythback kernel: ivtv: ==================== END INIT IVTV ====================

** dmesg | grep saa7127 **
saa7127: Unknown parameter `enable_output'
saa7127: Ignoring new-style parameters in presence of obsolete ones
saa7127: video encoder driver version V 0.3 loaded
saa7127: detecting saa7127 client on address 0x88
saa7127: Selecting NTSC video Standard
saa7127: Selecting S-Video+Composite
saa7127: Turn WSS off
saa7127: Widescreen Mode 4:3 Full Format
saa7127: Selecting Normal Encoder Input
saa7127: Enable Video Output
ivtv: i2c attach [client=saa7127[50],ok]
saa7127: Setting Encoder Video Standard
saa7127: Set NTSC Video Mode
saa7127: Selecting NTSC video Standard
saa7127: detecting saa7127 client on address 0x88
saa7127: Selecting NTSC video Standard
saa7127: Selecting S-Video+Composite
saa7127: Turn WSS off
saa7127: Widescreen Mode 4:3 Full Format
saa7127: Selecting Normal Encoder Input
saa7127: Enable Video Output
ivtv: i2c attach [client=saa7127[50],ok]

Thanks again!!

Steve
FedoraCore3
MythTv 18.1

__________________________________________________
Do You Yahoo!?
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com

bmayland at leoninedev

Jul 26, 2005, 8:09 AM

Post #7 of 15 (1936 views)
Permalink

Re: PVR 350 (TV-Out) and PVR 150 [In reply to]

Steve Nuffer wrote:

> saa7127: detecting saa7127 client on address 0x88
> ivtv: i2c attach [client=saa7127[50],ok]
> saa7127: detecting saa7127 client on address 0x88
> ivtv: i2c attach [client=saa7127[50],ok]
>
Lies! There can be only one! For some reason it isn't respecting
your i2c_enable module parameter. The second set should have a line
that says "saa7127 client id: saa7127_i2c_id 1, skipped". I'd suggest
getting up to version 0.3.7, which changes how the i2c_enable is handled
by the module.

-------------------------------------------------------
SF.Net email is sponsored by: Discover Easy Linux Migration Strategies
from IBM. Find simple to follow Roadmaps, straightforward articles,
informative Webcasts and more! Get everything you need to get up to
speed, fast. http://ads.osdn.com/?ad_id=7477&alloc_id=16492&op=click
_______________________________________________
ivtv-devel mailing list
ivtv-devel [at] lists
https://lists.sourceforge.net/lists/listinfo/ivtv-devel

nuffersp at yahoo

Jul 26, 2005, 11:27 AM

Post #8 of 15 (1941 views)
Permalink

Re: PVR 350 (TV-Out) and PVR 150 [In reply to]

> Lies! There can be only one! For some reason it isn't respecting
>your i2c_enable module parameter. The second set should have a line
> that says "saa7127 client id: saa7127_i2c_id 1, skipped". I'd suggest
> getting up to version 0.3.7, which changes how the i2c_enable is handled
> by the module.

I will upgrade. I'm currently using the "rpms" from the at-rpms site and there is appears there are no 3.7 versions available. Are these the steps to do this?

Remove all the following rpms (rpm -qa |grep ivtv)

ivtv-firmware-audio-0.0.1-1.at
ivtvdev-0.10-2.rhfc3.at
ivtv-kmdl-2.6.11-1.27_FC3-0.3.5l-92.rhfc3.at
ivtv-firmware-dec-2.02.023-4.at
ivtv-kmdl-2.6.11-1.35_FC3-0.3.6w-94.rhfc3.at
ivtv-firmware-enc-2.04.024-4.at
perl-Video-ivtv-0.13-7.rhfc3.at
ivtv-0.3.6w-94.rhfc3.at

Compile (configure, make, make install) the following or use existing RPM?

http://www.ivtv.tv/releases/ivtv-0.3/ivtv-0.3.7a.tgz

Do I need to do anything else? Is this all the software needed?

Thanks for your help.

Steve

---------------------------------
Do you Yahoo!?
Yahoo! Mail - You care about security. So do we.

agforsyth at gmail

Jul 26, 2005, 11:33 AM

Post #9 of 15 (1934 views)
Permalink

Re: PVR 350 (TV-Out) and PVR 150 [In reply to]

Remove the ivtvdev, ivtv-kmdl, and ivtv rpms but not the
perl-Video-ivtv or ivtv-firmware-* rpms.

Then make and make install the source. Remember to depmod -a as well.

On 7/26/05, Steve Nuffer <nuffersp [at] yahoo> wrote:
>
>
> > Lies! There can be only one! For some reason it isn't respecting
> >your i2c_enable module parameter. The second set should have a line
> > that says "saa7127 client id: saa7127_i2c_id 1, skipped". I'd suggest
> > getting up to version 0.3.7, which changes how the i2c_enable is handled
> > by the module.
>
> I will upgrade. I'm currently using the "rpms" from the at-rpms site and
> there is appears there are no 3.7 versions available. Are these the steps
> to do this?
>
> Remove all the following rpms (rpm -qa |grep ivtv)
>
>
> ivtv-firmware-audio-0.0.1-1.at
> ivtvdev-0.10-2.rhfc3.at
> ivtv-kmdl-2.6.11-1.27_FC3-0.3.5l-92.rhfc3.at
> ivtv-firmware-dec-2.02.023-4.at
> ivtv-kmdl-2.6.11-1.35_FC3-0.3.6w-94.rhfc3.at
> ivtv-firmware-enc-2.04.024-4.at
> perl-Video-ivtv-0.13-7.rhfc3.at
> ivtv-0.3.6w-94.rhfc3.at
>
> Compile (configure, make, make install) the following or use existing RPM?
>
>
> http://www.ivtv.tv/releases/ivtv-0.3/ivtv-0.3.7a.tgz
>
> Do I need to do anything else? Is this all the software needed?
>
> Thanks for your help.
>
> Steve
>
>
>
> ________________________________
> Do you Yahoo!?
> Yahoo! Mail - You care about security. So do we.
>
>

-------------------------------------------------------
SF.Net email is sponsored by: Discover Easy Linux Migration Strategies
from IBM. Find simple to follow Roadmaps, straightforward articles,
informative Webcasts and more! Get everything you need to get up to
speed, fast. http://ads.osdn.com/?ad_idt77&alloc_id492&op=click
_______________________________________________
ivtv-devel mailing list
ivtv-devel [at] lists
https://lists.sourceforge.net/lists/listinfo/ivtv-devel

lsymms at comcast

Jul 26, 2005, 3:20 PM

Post #10 of 15 (1963 views)
Permalink

Re: Re: PVR 350 (TV-Out) and PVR 150 [In reply to]

try removing:
options cx25840 i2c_enable=-1,1

Steve Nuffer wrote:

> I changed the modprobe.conf to the following with the same results.
>
> ** modprobe.conf **
> alias char-major-81 videodev
> alias char-major-81-0 ivtv
> alias char-major-81-1 ivtv
> options saa7127 enable_output=1 i2c_enable=1,-1
> options ivtv ivtv_debug=1 ivtv_std=1
> options cx25840 i2c_enable=-1,1
> install ivtv /sbin/modprobe --ignore-install ivtv; /sbin/modprobe ivtv-fb
> ** dmesg | grep ivtv ** ( the output was too large for the list )
> ivtv: ==================== START INIT IVTV ====================
> ivtv: version 0.3.6 (w) loading
> ivtv: Linux version: 2.6.11-1.35_FC3 686 REGPARM 4KSTACKS gcc-3.4
> ivtv: In case of problems please include the debug info
> ivtv: between the START INIT IVTV and END INIT IVTV lines when
> ivtv: mailing the ivtv-devel mailinglist.
> ivtv: Autodetected WinTV PVR 350 card
> ivtv: Found an iTVC15 based chip
> ivtv: Unreasonably low latency timer, setting to 64 (was 32)
> ivtv: XXX PCI device: 0x01e0 vendor: 0x10de
> ivtv: i2c attach [client=tveeprom[50],ok]
> msp34xx: ivtv version
> ivtv: i2c attach [client=MSP3448W-A2,ok]
> saa7115: starting probe for adapter ivtv i2c driver #0 (0x10005)
> ivtv: i2c attach [client=saa7115[50],ok]
> tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
> ivtv: i2c attach [client=(tuner unset),ok]
> ivtv: i2c attach [client=saa7127[50],ok]
> ivtv: Tuner Type 47, Tuner formats 0x00001000, Radio: yes, Model
> 0x00ad2598, Re vision 0x00000001
> ivtv: NTSC tuner detected
> ivtv: Radio detected
> ivtv: Encoder revision: 0x02040024
> ivtv: Encoder Firmware may be buggy, use version 0x02040011
> ivtv: Decoder revision: 0x02020023
> ivtv: Configuring WinTV PVR 350 card with 10 streams
> ivtv: Registered v4l2 device for encoder MPEG minor 0
> ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total)
> ivtv: Registered v4l2 device for encoder YUV minor 32
> ivtv: Create DMA encoder YUV stream: 0 x 10800 buffers (0KB total)
> ivtv: Registered v4l2 device for encoder VBI minor 224
> ivtv: Create DMA encoder VBI stream: 0 x 8736 buffers (0KB total)
> ivtv: Registered v4l2 device for encoder PCM audio minor 24
> ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total)
> ivtv: Registered v4l2 device for encoder radio minor 64
> ivtv: Create encoder radio stream
> ivtv: Registered v4l2 device for decoder MPEG minor 16
> ivtv: Create DMA decoder MPEG stream: 0 x 65536 buffe rs (0KB total)
> ivtv: Registered v4l2 device for decoder VBI minor 228
> ivtv: Create DMA decoder VBI stream: 0 x 2048 buffers (0KB total)
> ivtv: Registered v4l2 device for decoder VOUT minor 232
> ivtv: Create decoder VOUT stream
> ivtv: Registered v4l2 device for decoder YUV minor 48
> ivtv: Create DMA decoder YUV stream: 0 x 43200 buffers (0KB total)
> ivtv: Create DMA decoder OSD stream: 0 x 65536 buffers (0KB total)
> ivtv: Setting Tuner 47
> tuner: type set to 47 (LG NTSC (TAPE series)) by ivtv i2c driver #0
> ivtv: ivtv_enc_thread: pid = 585, itv = 0xe0cb29a0
> ivtv: ivtv_enc_vbi_thread: pid = 586, itv = 0xe0cb29a0
> ivtv: ivtv_dec_thread: pid = 587, itv = 0xe0cb29a0
> ivtv: ivtv_dec_vbi_thread: pid = 588, itv = 0xe0cb29a0
> ivtv: Setting audio matrix to input 3, output 1
> ivtv: Switching standard to NTSC.
> ivtv: Initialized WinTV PVR 350, card #0
> ivtv: Autodetected WinTV PVR 150 card
> ivtv: Found an iTVC16 based chip
> ivtv: Unreasonably low latency timer, setting to 64 (was 32)
> ivtv: XXX PCI device: 0x01e0 vendor: 0x10de
> ivtv: i2c attach [client=tveeprom[50],ok]
> saa7115: starting probe for adapter ivtv i2c driver #1 (0x10005)
> tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #1
> ivtv: i2c attach [client=(tuner unset),ok]
> ivtv: i2c attach [client=saa7127[50],ok]
> ivtv: Tuner Type 39, Tuner formats 0x00001000, Radio: yes, Model
> 0x008d1612, Revision 0x00000000
> ivtv: Radio detected
> ivtv: Encoder revision: 0x02040024
> ivtv: Encoder Firmware may be buggy, use version 0x02040011
> ivtv: Configuring WinTV PVR 150 card with 5 streams
> ivtv: Registered v4l2 device for encoder MPEG minor 1
> ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total)
> ivtv: Registered v4l2 device for encoder YUV minor 33
> ivtv: Create DMA encoder YUV stream: 0 x 10800 buffers (0KB total)
> ivtv: Registered v4l2 device for encoder VBI minor 225
> ivtv: Create DMA encoder VBI stream: 0 x 8736 buffers (0KB total)
> ivtv: Registered v4l2 device for encoder PCM audio minor 25
> ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total)
> ivtv: Registered v4l2 device for encoder radio minor 65
> ivtv: Create encoder radio stream
> ivtv: Setting Tuner 39
> tuner: type set to 39 (LG NTSC (newer TAPC series)) by ivtv i2c driver #1
> ivtv: Switching standard to NTSC.
> ivtv: Initialized WinTV PVR 150, card #1
> ivtv: ==================== END INIT IVTV ====================
> ivtv: ivtv_enc_thread: pid = 608, itv = 0xe0cd5f54
> ivtv: ivtv_enc_vbi_thread: pid = 609, itv = 0xe0cd5f54
> ivtv-osd: Framebuffer module loaded (attached to ivtv card id 0)
> ivtv-osd: Framebuffer is at decoder-relative address 0x00510000 and
> has 1704960 bytes.
> ivtv-osd: screen coords: [0 0] -> [720 480]
> ivtv-osd: original global alpha = 208
> ivtv-osd: current OSD state = 39
> ivtv-osd: new global alpha = 208 (1 255 0)
> ivtv-osd: framebuffer at 0xe1510000, mapp ed to 0xe1b90000, size 1350k
> ivtv-osd: mode is 720x480x32, linelength=2880
> ivtv-osd: fb1: iTVC15 TV out frame buffer device
> ivtv: Allocate DMA decoder OSD stream: 16 x 65536 buffers (1024KB total)
> ivtv: i2c attach [client=Hauppauge IR,ok]
> ivtv: i2c attach [client=Hauppauge IR (PVR150),ok]
> ivtv: Tried to open YUV output device but need to send data to mpeg
> decoder before it can be used
> ivtv: Tried to open YUV output device but need to send data to mpeg
> decoder before it can be used
> ivtv: Tried to open YUV output device but need to send data to mpeg
> decoder before it can be used
> ivtv: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
> ivtv: Setup VBI API header 0x0000bd0d pkts 1 buffs 4 ln 24 sz 1456
> ivtv: Setup VBI start 0x0018ea04 frames 4 fpi 1 lines 0x00000140
>
> __________________________________________________
> Do You Yahoo!?
> Tired of spam? Yahoo! Mail has the best spam protection around
> http://mail.yahoo.c om
>

-------------------------------------------------------
SF.Net email is sponsored by: Discover Easy Linux Migration Strategies
from IBM. Find simple to follow Roadmaps, straightforward articles,
informative Webcasts and more! Get everything you need to get up to
speed, fast. http://ads.osdn.com/?ad_id=7477&alloc_id=16492&op=click
_______________________________________________
ivtv-devel mailing list
ivtv-devel [at] lists
https://lists.sourceforge.net/lists/listinfo/ivtv-devel

nuffersp at yahoo

Jul 26, 2005, 8:37 PM

Post #11 of 15 (1954 views)
Permalink

Re: PVR 350 (TV-Out) and PVR 150 [In reply to]

No change on the output. I tried several different scenarios.

1) Only aliases defined in modprobe.conf. - No Change
2) Removed no_black_magic - No change
3) Removed i2c_enable on both, on only one, then only the other - No Change

The following output is with this modprobe.conf file.

** /etc/modprobe.conf **
alias char-major-81 videodev
alias char-major-81-0 ivtv
alias char-major-81-1 ivtv
options saa7127 i2c_enable=1,-1 output_select=1
options cx25840 i2c_enable=-1,1 no_black_magic=1
options ivtv ivtv_debug=1
install ivtv /sbin/modprobe --ignore-install ivtv; /sbin/modprobe ivtv-fb

** ivtv output **
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.3.6 (w) loading
ivtv: Linux version: 2.6.11-1.35_FC3 686 REGPARM 4KSTACKS gcc-3.4
ivtv: In case of problems please include the debug info
ivtv: between the START INIT IVTV and END INIT IVTV lines when
ivtv: mailing the ivtv-devel mailinglist.
ivtv: Autodetected WinTV PVR 350 card
ivtv: Found an iTVC15 based chip
ivtv: Unreasonably low latency timer, setting to 64 (was 32)
ivtv: XXX PCI device: 0x01e0 vendor: 0x10de
ivtv: i2c attach [client=tveeprom[50],ok]
msp34xx: ivtv version
ivtv: i2c attach [client=MSP3448W-A2,ok]
saa7115: starting probe for adapter ivtv i2c driver #0 (0x10005)
ivtv: i2c attach [client=saa7115[50],ok]
tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
ivtv: i2c attach [client=(tuner unset),ok]
ivtv: i2c attach [client=saa7127[50],ok]
ivtv: Tuner Type 47, Tuner formats 0x00001000, Radio: yes, Model 0x00ad2598, Revision 0x00000001
ivtv: NTSC tuner detected
ivtv: Radio detected
ivtv: Encoder revision: 0x02040024
ivtv: Encoder Firmware may be buggy, use version 0x02040011
ivtv: Decoder revision: 0x02020023
ivtv: Configuring WinTV PVR 350 card with 10 streams
ivtv: Registered v4l2 device for encoder MPEG minor 0
ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total)
ivtv: Registered v4l2 device for encoder YUV minor 32
ivtv: Create DMA encoder YUV stream: 0 x 10800 buffers (0KB total)
ivtv: Registered v4l2 device for encoder VBI minor 224
ivtv: Create DMA encoder VBI stream: 0 x 8736 buffers (0KB total)
ivtv: Registered v4l2 device for encoder PCM audio minor 24
ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total)
ivtv: Registered v4l2 device for encoder radio minor 64
ivtv: Create encoder radio stream
ivtv: Registered v4l2 device for decoder MPEG minor 16
ivtv: Create DMA decoder MPEG stream: 0 x 65536 buffers (0KB total)
ivtv: Registered v4l2 device for decoder VBI minor 228
ivtv: Create DMA decoder VBI stream: 0 x 2048 buffers (0KB total)
ivtv: Registered v4l2 device for decoder VOUT minor 232
ivtv: Create decoder VOUT stream
ivtv: Registered v4l2 device for decoder YUV minor 48
ivtv: Create DMA decoder YUV stream: 0 x 43200 buffers (0KB total)
ivtv: Create DMA decoder OSD stream: 0 x 65536 buffers (0KB total)
ivtv: Setting Tuner 47
tuner: type set to 47 (LG NTSC (TAPE series)) by ivtv i2c driver #0
ivtv: ivtv_enc_thread: pid = 585, itv = 0xe0cb29a0
ivtv: ivtv_enc_vbi_thread: pid = 586, itv = 0xe0cb29a0
ivtv: ivtv_dec_thread: pid = 587, itv = 0xe0cb29a0
ivtv: ivtv_dec_vbi_thread: pid = 588, itv = 0xe0cb29a0
ivtv: Setting audio matrix to input 3, output 1
ivtv: Switching standard to NTSC.
ivtv: Initialized WinTV PVR 350, card #0
ivtv: Autodetected WinTV PVR 150 card
ivtv: Found an iTVC16 based chip
ivtv: Unreasonably low latency timer, setting to 64 (was 32)
ivtv: XXX PCI device: 0x01e0 vendor: 0x10de
ivtv: i2c attach [client=tveeprom[50],ok]
saa7115: starting probe for adapter ivtv i2c driver #1 (0x10005)
tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #1
ivtv: i2c attach [client=(tuner unset),ok]
ivtv: i2c attach [client=saa7127[50],ok]
ivtv: Tuner Type 39, Tuner formats 0x00001000, Radio: yes, Model 0x008d1612, Revision 0x00000000
ivtv: Radio detected
ivtv: Encoder revision: 0x02040024
ivtv: Encoder Firmware may be buggy, use version 0x02040011
ivtv: Configuring WinTV PVR 150 card with 5 streams
ivtv: Registered v4l2 device for encoder MPEG minor 1
ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total)
ivtv: Registered v4l2 device for encoder YUV minor 33
ivtv: Create DMA encoder YUV stream: 0 x 10800 buffers (0KB total)
ivtv: Registered v4l2 device for encoder VBI minor 225
ivtv: Create DMA encoder VBI stream: 0 x 8736 buffers (0KB total)
ivtv: Registered v4l2 device for encoder PCM audio minor 25
ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total)
ivtv: Registered v4l2 device for encoder radio minor 65
ivtv: Create encoder radio stream
ivtv: Setting Tuner 39
tuner: type set to 39 (LG NTSC (newer TAPC series)) by ivtv i2c driver #1
ivtv: Switching standard to NTSC.
ivtv: Initialized WinTV PVR 150, card #1
ivtv: ==================== END INIT IVTV ====================

**** NOTE ****
Notice the "Ignoring new-style..." comment below. Could it be ignoring the line "options saa7127 i2c_enable=1,-1" because of the enable_output line. I didn't specify that but why is it showing up?
**** NOTE ****

# dmesg | grep saa7127
saa7127: Unknown parameter `enable_output'
saa7127: Ignoring new-style parameters in presence of obsolete ones
saa7127: video encoder driver version V 0.3 loaded
saa7127: detecting saa7127 client on address 0x88
saa7127: Selecting NTSC video Standard
saa7127: Selecting S-Video+Composite
saa7127: Turn WSS off
saa7127: Widescreen Mode 4:3 Full Format
saa7127: Selecting Normal Encoder Input
saa7127: Enable Video Output
ivtv: i2c attach [client=saa7127[50],ok]
saa7127: Setting Encoder Video Standard
saa7127: Set NTSC Video Mode
saa7127: Selecting NTSC video Standard
saa7127: detecting saa7127 client on address 0x88
saa7127: Selecting NTSC video Standard
saa7127: Selecting S-Video+Composite
saa7127: Turn WSS off
saa7127: Widescreen Mode 4:3 Full Format
saa7127: Selecting Normal Encoder Input
saa7127: Enable Video Output

# rpm -qa | grep ivtv
ivtv-firmware-audio-0.0.1-1.at
ivtv-firmware-dec-2.02.023-4.at
ivtv-firmware-enc-2.04.024-4.at
perl-Video-ivtv-0.13-7.rhfc3.at
ivtvdev-0.10-2.rhfc3.at

Steve

__________________________________________________
Do You Yahoo!?
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com

nuffersp at yahoo

Jul 28, 2005, 7:56 AM

Post #12 of 15 (1924 views)
Permalink

Re: PVR 350 (TV-Out) and PVR 150 [In reply to]

I now have my PVR350 and PVR150 working fine with the ivtv 0.3.7a and Fedora Core3. Since everyone has been so helpful, I wanted to provide some feedback on how I resolved this.

PVR-350 Working with Fedora and ivtv 0.2.0-rc3j
Added a PVR 150 and assumed that I needed ivtv 0.3.x
(Still not sure if I needed to upgrade)
Upgraded to ivtv 0.3.6w using atrpms
For some reason, the option to disable saa7127 on the PVR 150 wasn�t working
options saa7127 i2c_enable=1,-1
Suggestion about upgrading to 0.3.7a since this handles the drivers differently
Removed some RPMs (ivtvdev, ivtv-kmdl, and ivtv rpms)
Compiled and installed 0.3.7a
For some reason, the same problem persisted with the options. I also noticed that the version from the /var/log/messages still showed 0.3.6w.
Since I had used �mkinitrd-ivtv /boot/initrd-`uname -r`.img `uname -r`� the old version was still in the RAM disk.
Tried rerunning the command but it failed looking for tveeprom-ivtv. I did not try the suggestion about removing the ivtv from the program.
I rebuilt the RAM disk with �mkinitrd -f /boot/initrd-`uname -r`.img `uname -r`�
Rebooted
PVR 150 and PVR 350 works

For detail see above.

** /etc/modprobe.conf ***

# ivtv modules setup

alias char-major-81 videodev

alias char-major-81-0 ivtv

alias char-major-81-1 ivtv

# Use following two lines for PVR350 Svideo-Out with frame buffer

options saa7127 i2c_enable=1,-1 output_select=1

install ivtv /sbin/modprobe --ignore-install ivtv; /sbin/modprobe ivtv-fb

Thanks to all. Now onto the next part of Myth.

Steve

---------------------------------
Start your day with Yahoo! - make it your home page

ryszard99 at gmail

Jul 29, 2005, 12:26 AM

Post #13 of 15 (1915 views)
Permalink

Re: Re: PVR 350 (TV-Out) and PVR 150 [In reply to]

Hi Steve,

with the tv out on your 350, are you running X out of it, and if so,
have you tried xvid or divx's out of it? i'm interested in the
performance .. ;-)

i've not been able to get decent performance (they look like they're
running in slow mo). admitadly the last time i tried was about 9
months ago, so things have probably changed a bit since then...

regs
Jason

On 7/28/05, Steve Nuffer <nuffersp [at] yahoo> wrote:
>
>
> I now have my PVR350 and PVR150 working fine with the ivtv 0.3.7a and Fedora
> Core3. Since everyone has been so helpful, I wanted to provide some
> feedback on how I resolved this.
>
>
>
> PVR-350 Working with Fedora and ivtv 0.2.0-rc3j
> Added a PVR 150 and assumed that I needed ivtv 0.3.x
> (Still not sure if I needed to upgrade)
> Upgraded to ivtv 0.3.6w using atrpms
> For some reason, the option to disable saa7127 on the PVR 150 wasn't working
> options saa7127 i2c_enable=1,-1
> Suggestion about upgrading to 0.3.7a since this handles the drivers
> differently
> Removed some RPMs (ivtvdev, ivtv-kmdl, and ivtv rpms)
> Compiled and installed 0.3.7a
> For some reason, the same problem persisted with the options. I also
> noticed that the version from the /var/log/messages still showed 0.3.6w.
> Since I had used "mkinitrd-ivtv /boot/initrd-`uname -r`.img `uname -r`" the
> old version was still in the RAM disk.
> Tried rerunning the command but it failed looking for tveeprom-ivtv. I did
> not try the suggestion about removing the ivtv from the program.
> I rebuilt the RAM disk with "mkinitrd -f /boot/initrd-`uname -r`.img `uname
> -r`"
> Rebooted
> PVR 150 and PVR 350 works
>
> For detail see above.
>
>
>
> ** /etc/modprobe.conf ***
>
> # ivtv modules setup
>
> alias char-major-81 videodev
>
> alias char-major-81-0 ivtv
>
> alias char-major-81-1 ivtv
>
> # Use following two lines for PVR350 Svideo-Out with frame buffer
>
> options saa7127 i2c_enable=1,-1 output_select=1
>
> install ivtv /sbin/modprobe --ignore-install ivtv; /sbin/modprobe ivtv-fb
>
>
>
> Thanks to all. Now onto the next part of Myth.
>
>
>
> Steve
>
>
> ________________________________
> Start your day with Yahoo! - make it your home page
>
>

-------------------------------------------------------
SF.Net email is Sponsored by the Better Software Conference & EXPO September
19-22, 2005 * San Francisco, CA * Development Lifecycle Practices
Agile & Plan-Driven Development * Managing Projects & Teams * Testing & QA
Security * Process Improvement & Measurement * http://www.sqe.com/bsce5sf
_______________________________________________
ivtv-devel mailing list
ivtv-devel [at] lists
https://lists.sourceforge.net/lists/listinfo/ivtv-devel

nuffersp at yahoo

Jul 29, 2005, 11:40 AM

Post #14 of 15 (1899 views)
Permalink

Re: PVR 350 (TV-Out) and PVR 150 [In reply to]

I am running X through the Svideo.

When I watched a DVD for the first time it was as you described choppy and slow. I then read about using Xine which helped a lot.

DVD Player: xine -f -I -V xshm --audio-driver alsa --no-logo --no-splash dvd://

I'm new and still trying to understand the environement. I would also like to try "xv" output through Svideo. If you know how, could you share some information.

I hope this answers your question.

Steve

__________________________________________________
Do You Yahoo!?
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com

ivtv at archer-segel

Jul 29, 2005, 6:41 PM

Post #15 of 15 (1900 views)
Permalink

Re: Re: PVR 350 (TV-Out) and PVR 150 [In reply to]

Steve Nuffer wrote:

> I'm new and still trying to understand the environement. I would also
> like to try "xv" output through Svideo. If you know how, could you
> share some information.
>
Just replace 'xshm' with 'xv', like this:

xine -pfhq -V xv --no-splash dvd://

Daniel

-------------------------------------------------------
SF.Net email is sponsored by: Discover Easy Linux Migration Strategies
from IBM. Find simple to follow Roadmaps, straightforward articles,
informative Webcasts and more! Get everything you need to get up to
speed, fast. http://ads.osdn.com/?ad_id=7477&alloc_id=16492&op=click
_______________________________________________
ivtv-devel mailing list
ivtv-devel [at] lists
https://lists.sourceforge.net/lists/listinfo/ivtv-devel

Index | Next | Previous | View Threaded

Interested in having your list archived? Contact Gossamer Threads