Mailing List Archive: Cisco: VOIP

VWIC2-2MFT-T1/E1 for non-voice data ?

Index | Next | Previous | View Threaded

svoll.voip at gmail

Nov 19, 2009, 8:23 AM

Post #1 of 5 (953 views)
Permalink

VWIC2-2MFT-T1/E1 for non-voice data ?

Can I use a VWIC2-2MFT-T1/E1 for just a point to point data T1?

if so, how do I get the serial interfaces setup? I can add card type, but
then I get a controller T1 like it's a voice PRI not a regular t1 data
interface serial x/x/x

Thanks

Scott

bms314 at gmail

Nov 19, 2009, 8:40 AM

Post #2 of 5 (928 views)
Permalink

Re: VWIC2-2MFT-T1/E1 for non-voice data ? [In reply to]

controller T1 X/X/X
channel-group 0 timeslots 1-24

That should do it for you.

Brian

On Thu, Nov 19, 2009 at 10:23 AM, Scott Voll <svoll.voip [at] gmail> wrote:

> Can I use a VWIC2-2MFT-T1/E1 for just a point to point data T1?
>
> if so, how do I get the serial interfaces setup? I can add card type, but
> then I get a controller T1 like it's a voice PRI not a regular t1 data
> interface serial x/x/x
>
> Thanks
>
> Scott
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip [at] puck
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>

MLoraditch at heliontechnologies

Nov 19, 2009, 8:41 AM

Post #3 of 5 (916 views)
Permalink

Re: VWIC2-2MFT-T1/E1 for non-voice data ? [In reply to]

controller T1 0/0/0
channel-group 0 timeslots 1-24

Configure the controllers as such. You will then get serial0/0/0:0 and that acts just like a regular data only t1

Matthew Loraditch
1965 Greenspring Drive
Timonium, MD 21093
support [at] heliontechnologies<mailto:support [at] heliontechnologies>
(p) (410) 252-8830
(F) (443) 541-1593

Visit us at www.heliontechnologies.com<http://www.heliontechnologies.com>
Support Issue? Email support [at] heliontechnologies<mailto:support [at] heliontechnologies> for fast assistance!

From: cisco-voip-bounces [at] puck [mailto:cisco-voip-bounces [at] puck] On Behalf Of Scott Voll
Sent: Thursday, November 19, 2009 11:23 AM
To: cisco-voip [at] puck
Subject: [cisco-voip] VWIC2-2MFT-T1/E1 for non-voice data ?

Can I use a VWIC2-2MFT-T1/E1 for just a point to point data T1?

if so, how do I get the serial interfaces setup? I can add card type, but then I get a controller T1 like it's a voice PRI not a regular t1 data interface serial x/x/x

Thanks

Scott

svoll.voip at gmail

Nov 19, 2009, 9:12 AM

Post #4 of 5 (919 views)
Permalink

Re: VWIC2-2MFT-T1/E1 for non-voice data ? [In reply to]

Thanks guys.

This is my first new gen card for data T1s.

Scott

On Thu, Nov 19, 2009 at 8:41 AM, Matthew Loraditch <
MLoraditch [at] heliontechnologies> wrote:

> controller T1 0/0/0
>
> channel-group 0 timeslots 1-24
>
>
>
> Configure the controllers as such. You will then get serial0/0/0:0 and that
> acts just like a regular data only t1
>
>
>
>
>
> *Matthew Loraditch*
> 1965 Greenspring Drive
>
> Timonium, MD 21093
> support [at] heliontechnologies
> (p) (410) 252-8830
> (F) (443) 541-1593
>
> Visit us at www.heliontechnologies.com
> Support Issue? Email support [at] heliontechnologies for fast assistance!
>
>
>
> *From:* cisco-voip-bounces [at] puck [mailto:
> cisco-voip-bounces [at] puck] *On Behalf Of *Scott Voll
> *Sent:* Thursday, November 19, 2009 11:23 AM
> *To:* cisco-voip [at] puck
> *Subject:* [cisco-voip] VWIC2-2MFT-T1/E1 for non-voice data ?
>
>
>
> Can I use a VWIC2-2MFT-T1/E1 for just a point to point data T1?
>
>
>
> if so, how do I get the serial interfaces setup? I can add card type, but
> then I get a controller T1 like it's a voice PRI not a regular t1 data
> interface serial x/x/x
>
>
>
> Thanks
>
>
>
> Scott
>

jim at tgasolutions

Nov 21, 2009, 4:49 PM

Post #5 of 5 (879 views)
Permalink

Re: VWIC2-2MFT-T1/E1 for non-voice data ? [In reply to]

Don't forget to set the card type as t1..
http://www.cisco.com/en/US/products/hw/modules/ps2617/products_configuration_example09186a008052c920.shtml

Jim

From: cisco-voip-bounces [at] puck [mailto:cisco-voip-bounces [at] puck] On Behalf Of Scott Voll
Sent: Thursday, November 19, 2009 12:13 PM
To: Matthew Loraditch; bms314 [at] gmail
Cc: cisco-voip [at] puck
Subject: Re: [cisco-voip] VWIC2-2MFT-T1/E1 for non-voice data ?

Thanks guys.

This is my first new gen card for data T1s.

Scott
On Thu, Nov 19, 2009 at 8:41 AM, Matthew Loraditch <MLoraditch [at] heliontechnologies<mailto:MLoraditch [at] heliontechnologies>> wrote:
controller T1 0/0/0
channel-group 0 timeslots 1-24

Configure the controllers as such. You will then get serial0/0/0:0 and that acts just like a regular data only t1

Matthew Loraditch
1965 Greenspring Drive
Timonium, MD 21093
support [at] heliontechnologies<mailto:support [at] heliontechnologies>
(p) (410) 252-8830
(F) (443) 541-1593

Visit us at www.heliontechnologies.com<http://www.heliontechnologies.com>
Support Issue? Email support [at] heliontechnologies<mailto:support [at] heliontechnologies> for fast assistance!

From: cisco-voip-bounces [at] puck<mailto:cisco-voip-bounces [at] puck> [mailto:cisco-voip-bounces [at] puck<mailto:cisco-voip-bounces [at] puck>] On Behalf Of Scott Voll
Sent: Thursday, November 19, 2009 11:23 AM
To: cisco-voip [at] puck<mailto:cisco-voip [at] puck>
Subject: [cisco-voip] VWIC2-2MFT-T1/E1 for non-voice data ?

Can I use a VWIC2-2MFT-T1/E1 for just a point to point data T1?

if so, how do I get the serial interfaces setup? I can add card type, but then I get a controller T1 like it's a voice PRI not a regular t1 data interface serial x/x/x

Thanks

Scott

Index | Next | Previous | View Threaded

Interested in having your list archived? Contact Gossamer Threads