asobihoudai at yahoo
Jul 1, 2009, 7:55 PM
Post #9 of 14
(3628 views)
Permalink
|
As you can see you have a PVDM2-8.
You're lacking two channels. You'll have to either add another PVDM2-8 (or something else smaller than that..I don't think there is anything smaller than that...) or you can buy yourself a PVDM2-16 and install that.
Get ready to cough a few thousand dollars for that...
________________________________
From: Jeffrey S. McNeal <jmcneal [at] vtg>
To: Karen Cheng <kcheng [at] thiess>; Mike Thompson <mthompson729 [at] gmail>; cisco-voip [at] puck
Sent: Wednesday, July 1, 2009 10:52:21 PM
Subject: Re: [cisco-voip] Cisco 2801 - PRI
Here is the show inventory
NAME: "2801 chassis", DESCR: "2801 chassis, Hw Serial#: 1018444029, Hw Revision:
5.0"
PID: CISCO2801 , VID: V01 , SN: FTX0947W01Q
NAME: "C2801 Motherboard with 2 Fast Ethernet", DESCR: "C2801 Motherboard with 2
Fast Ethernet"
PID: CISCO2801 , VID: 5.0, SN: FTX0947W01Q
NAME: "VIC 0", DESCR: "2nd generation four port FXO voice interface daughtercard
"
PID: VIC2-4FXO , VID: V01 , SN: FOC10470UU9
NAME: "voice-port 0/0/0", DESCR: "Foreign Exchange Office 0/0/0"
PID: Foreign Exchange Office 0/0/0, VID: , SN:
NAME: "voice-port 0/0/1", DESCR: "Foreign Exchange Office 0/0/1"
PID: Foreign Exchange Office 0/0/1, VID: , SN:
NAME: "voice-port 0/0/2", DESCR: "Foreign Exchange Office 0/0/2"
PID: Foreign Exchange Office 0/0/2, VID: , SN:
NAME: "voice-port 0/0/3", DESCR: "Foreign Exchange Office 0/0/3"
PID: Foreign Exchange Office 0/0/3, VID: , SN:
NAME: "WIC/VIC/HWIC 1", DESCR: "Two port T1 voice interface daughtercard"
PID: VWIC-2MFT-T1= , VID: 1.0, SN: 33551376
NAME: "WIC/VIC/HWIC 3", DESCR: "9 Port FE Switch"
PID: HWIC-D-9ESW , VID: VN/A, SN: FOC09173HVE
NAME: "WIC/VIC/HWIC 3 Power Daughter Card", DESCR: "9-Port HWIC-ESW Power Daught
er Card"
PID: ILPM-8 , VID: VN/A, SN: FOC09173HLY
NAME: "PVDMII DSP SIMM with one DSP with half channel capcity", DESCR: "PVDMII D
SP SIMM with one DSP with half channel capcity"
PID: PVDM2-8 , VID: NA , SN: FOC091229KT
Jeffrey S. McNeal
Vision Technology Group, LLC
125 West Bruce Street
Harrisonburg, VA 22801
(540) 437-0112 - Office
(540) 437-0129 - Fax
________________________________
From: Karen Cheng [mailto:kcheng [at] thiess]
Sent: Wed 7/1/2009 10:46 PM
To: Jeffrey S. McNeal; Mike Thompson; cisco-voip [at] puck
Subject: RE: [cisco-voip] Cisco 2801 - PRI
If you do a sow inventory on the router it will show you the amount of DSP’s you have installed in the router. Moving the PRI card from one router to another will achieve nothing more than allowing a connection point for the ISDN.
You will at least 1 DSP per channel that your ISDN service has, eg if it is a 30 channel ISDN then you need at least 30 DSP’s (comes in certain numbers though).
Karen Cheng
Network Engineer - ICT
Thiess Business Services
Thiess Pty Ltd
179 Grey Street | South Bank QLD 4101
T +61 7 3002 9807
F +61 7 3002 9829
M 0437 549 439
www.thiess.com.au
From:cisco-voip-bounces [at] puck [mailto:cisco-voip-bounces [at] puck] On Behalf Of Jeffrey S. McNeal
Sent: Thursday, 2 July 2009 12:31 PM
To: Mike Thompson; cisco-voip [at] puck
Subject: Re: [cisco-voip] Cisco 2801 - PRI
There is only 1 PRI. I have a 2 T1 card 1 for a metro t1 and then the other I was going to use for the PRI.
Jeffrey S. McNeal
Vision Technology Group, LLC
125 West Bruce Street
Harrisonburg, VA 22801
(540) 437-0112 - Office
(540) 437-0129 - Fax
________________________________
From:Mike Thompson [mailto:mthompson729 [at] gmail]
Sent: Wed 7/1/2009 10:25 PM
To: Jeffrey S. McNeal; cisco-voip [at] puck
Subject: RE: [cisco-voip] Cisco 2801 - PRI
Need to have PVDM2-XX (need 24 total channels total channels: type show diag and look for PVDM, add em up and you’ll get the total).
Keep in mind that a 2801 only supports a TOTAL of 30 PVDM channels.
2801 only supports 1 PRI, so if this isn’t the first one, that’s the issue.
Have to have ISDN switch type set first
Let me know what you get.
From:cisco-voip-bounces [at] puck [mailto:cisco-voip-bounces [at] puck] On Behalf Of Jeffrey S. McNeal
Sent: Wednesday, July 01, 2009 10:17 PM
To: cisco-voip [at] puck
Subject: [cisco-voip] Cisco 2801 - PRI
Hello All,
I am trying to configure a pri on a cisco 2801 but I get the following message:
(config-controller)#pri-group timeslots 1-24
% Not enough DSP resources available to configure pri-group on controller T1 0/1
/1
% The remaining dsp resources are enough for 4 time slots.
% For current codec complexity, 2 extra dsp(s) are required to create this voice
port.
Can I fix it or is something wrong?
Jeffrey S. McNeal
Vision Technology Group, LLC
125 West Bruce Street
Harrisonburg, VA 22801
(540) 437-0112 - Office
(540) 437-0129 - Fax
______________________________________________________________________
This email has been scanned by the MessageLabs Email Security System.
For more information please visit http://www.messagelabs.com/email
______________________________________________________________________
_____________________________________________________________________
IMPORTANT - This email and any attachments may be confidential and privileged. If received in error, please contact Thiess and delete all copies. You may not rely on advice and documents received by email unless confirmed by a signed Thiess letter. This restriction on reliance will not apply to the extent that the above email communication is between parties to a contract and is authorised under that contract. Before opening or using attachments, check them for viruses and defects. Thiess' liability is limited to resupplying any affected attachments.
_______________________________________________
cisco-voip mailing list
cisco-voip [at] puck
https://puck.nether.net/mailman/listinfo/cisco-voip
|
