chris at uplogon
Jun 13, 2012, 2:29 PM
Post #5 of 7
(642 views)
Permalink
|
|
Re: 7204VXR NPE G1 Upgrade from 12.4 to 15.1M Issues
[In reply to]
|
|
I didn't have time to check. Going to bring it down again tonight and
run more tests. Also thinking i might default the router config and
build it back up piece by piece to see if i can find the issue.
On 6/13/2012 4:22 PM, Chuck Church wrote:
> Probably not a single reference. Have you verified on the outside world
> that your prefixes are seen? If you haven't, what are they, most people on
> this list can verify. Obviously you'd have to do that while running 15.1...
>
> Chuck
>
>
> -----Original Message-----
> From: Chris Gotstein [mailto:chris [at] uplogon]
> Sent: Wednesday, June 13, 2012 5:16 PM
> To: Chuck Church
> Cc: 'cisco-nsp'
> Subject: Re: [c-nsp] 7204VXR NPE G1 Upgrade from 12.4 to 15.1M Issues
>
> Prefix-lists remained the same. Verified that.
>
> Is there a list somewhere of the default commands for 12.4 and 15.1M?
>
> On 6/13/2012 4:10 PM, Chuck Church wrote:
>> Did you confirm that the prefixes you were sending via BGP under 12.4
>> didn't disappear when running 15.1? Are your peers still accepting
>> them? It's possible a default changed that is affecting your
> advertisement.
>>
>> Chuck
>>
>> -----Original Message-----
>> From: cisco-nsp-bounces [at] puck
>> [mailto:cisco-nsp-bounces [at] puck] On Behalf Of Chris Gotstein
>> Sent: Wednesday, June 13, 2012 4:35 PM
>> To: cisco-nsp
>> Subject: [c-nsp] 7204VXR NPE G1 Upgrade from 12.4 to 15.1M Issues
>>
>> I have a 7204VXR with NPE-G1 that is running 12.4.25f Advanced Services.
>> This router is acting as our main connection to the internet running
>> full BGP routing connected to 2 providers via ethernet. I'm wanting
>> to upgrade to 15.1M Advanced Services w/ LI. After loading the router
>> with IOS 15.1M, the router comes up correctly, all BGP sessions come
>> up correctly and the routing table looks correct. I can ping the outside
> world from the router.
>> When i try to access the internet from another station, all traffic
>> dies at this router. I can ping all interfaces on the router from any
> workstation.
>> I have sanitized configs for those that would like to see them. This
>> is a pretty basic setup, not doing anything fancy. Soon as I load
>> 12.4 back on the router and reload, everything comes back up just fine.
> Any thoughts?
>>
>> --
>> ---- ---- ---- ----
>> Chris Gotstein, Network Engineer, U.P. Logon/Computer Connection U.P.
>> http://uplogon.com | +1 906 774 4847 | chris [at] uplogon
>>
>> _______________________________________________
>> cisco-nsp mailing list cisco-nsp [at] puck
>> https://puck.nether.net/mailman/listinfo/cisco-nsp
>> archive at http://puck.nether.net/pipermail/cisco-nsp/
>>
>
> --
> ---- ---- ---- ----
> Chris Gotstein, Network Engineer, U.P. Logon/Computer Connection U.P.
> http://uplogon.com | +1 906 774 4847 | chris [at] uplogon
>
>
--
---- ---- ---- ----
Chris Gotstein, Network Engineer, U.P. Logon/Computer Connection U.P.
http://uplogon.com | +1 906 774 4847 | chris [at] uplogon
_______________________________________________
cisco-nsp mailing list cisco-nsp [at] puck
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/
|
