jckdaniels12 at gmail
Aug 9, 2009, 9:55 PM
Views: 701
Permalink
|
Hi All
I'm getting below error on GSR 12416 ALARM CARD -
IOS 12.0(32)SY6
WARNING: Unknown MBUS agent controller type, slot 24
Contact your technical support
representative.<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<Please advise
sh diag 24
SLOT 24 (ALM 0 ): Alarm Module(16)
MAIN: type 64, 800-5570-05 rev C0
Deviation: 0
HW config: 0x00 SW key: 00-00-00
PCA: 73-4266-04 rev B0 ver 3
Design Release 1.0 S/N SAL1250CZJ9
MBUS: Unknown (0) 00-0000-00 rev 70 dev 0
HW version 1.2 S/N SAL1248BSQ5
Test hist: 0x00 RMA#: 00-00-00 RMA hist: 0x00
DIAG: Test count: 0x00000000 Test results: 0x00000000
FRU: Linecard/Module: GSR16-ALRM=
MBUS Agent Software version 2.68 (RAM) (ROM version is 3.66)
sh gsr
Slot 0 type = Modular SPA Interface Card
state = IOS RUN Line Card Enabled
subslot 0/0: SPA-1X10GE-L-V2 (0x50C), status is ok
subslot 0/1: Empty
subslot 0/2: Empty
subslot 0/3: Empty
Slot 5 type = Modular SPA Interface Card
state = IOS RUN Line Card Enabled
subslot 5/0: SPA-2XOC48POS/RPR (0x46F), status is ok
subslot 5/1: SPA-5X1GE-V2 (0x50A), status is ok
subslot 5/2: Empty
subslot 5/3: Empty
Slot 6 type = Modular SPA Interface Card
state = IOS RUN Line Card Enabled
subslot 6/0: SPA-4XT3/E3 (0x40B), status is ok
subslot 6/1: SPA-4XT3/E3 (0x40B), status is ok
subslot 6/2: SPA-8XOC3-POS (0x505), status is ok
subslot 6/3: SPA-8XOC3-POS (0x505), status is ok
Slot 7 type = Performance Route Processor
state = ACTV RP IOS Running ACTIVE
Slot 8 type = Performance Route Processor
state = STBY RP IOS Running STANDBY
Slot 9 type = Modular SPA Interface Card
state = IOS RUN Line Card Enabled
subslot 9/0: SPA-1X10GE-L-V2 (0x50C), status is ok
subslot 9/1: Empty
subslot 9/2: Empty
subslot 9/3: Empty
Slot 14 type = Modular SPA Interface Card
state = IOS RUN Line Card Enabled
subslot 14/0: SPA-2XOC48POS/RPR (0x46F), status is ok
subslot 14/1: SPA-5X1GE-V2 (0x50A), status is ok
subslot 14/2: Empty
subslot 14/3: Empty
Slot 15 type = Modular SPA Interface Card
state = IOS RUN Line Card Enabled
subslot 15/0: SPA-4XOC12-POS (0x507), status is ok
subslot 15/1: SPA-8XOC3-POS (0x505), status is ok
subslot 15/2: SPA-4XT3/E3 (0x40B), status is ok
subslot 15/3: Empty
Slot 16 type = Clock Scheduler Card OC192 Dual Priority
state = Card Powered
Slot 17 type = Clock Scheduler Card OC192 Dual Priority
state = Card Powered PRIMARY CLOCK
Slot 18 type = Switch Fabric Card 16XOC192
state = Card Powered
Slot 19 type = Switch Fabric Card 16XOC192
state = Card Powered
Slot 20 type = Switch Fabric Card 16XOC192
state = Card Powered
Slot 24 type = Alarm Module(16)
state = Card Powered
Slot 25 type = Alarm Module(16)
state = Card Powered
Slot 27 type = Bus Board(16)
state = Card Powered
Slot 28 type = Blower Module(16)
state = Card Powered
Slot 29 type = Blower Module(16)
state = Card Powered
Thanks and Regards
J.Daniels
_______________________________________________
cisco-nsp mailing list cisco-nsp [at] puck
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/
|
ALARM CARD ERROR
