jckdaniels12 at gmail
Aug 10, 2009, 7:45 PM
Post #3 of 3
(647 views)
Permalink
|
Hi,
opened just tac case and as per them its a hardware isssue .
Thanks and Regards
J.Daniels
On 8/10/09, Aaron <dudepron [at] gmail> wrote:
>
> Open a tac case.
>
> On Mon, Aug 10, 2009 at 00:55, jack daniels <jckdaniels12 [at] gmail>wrote:
>
>> Hi All
>>
>> I'm getting below error on GSR 12416 ALARM CARD -
>>
>> IOS 12.0(32)SY6
>>
>>
>>
>> WARNING: Unknown MBUS agent controller type, slot 24
>> Contact your technical support
>> representative.<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<Please advise
>>
>>
>>
>> sh diag 24
>>
>> SLOT 24 (ALM 0 ): Alarm Module(16)
>> MAIN: type 64, 800-5570-05 rev C0
>> Deviation: 0
>> HW config: 0x00 SW key: 00-00-00
>> PCA: 73-4266-04 rev B0 ver 3
>> Design Release 1.0 S/N SAL1250CZJ9
>> MBUS: Unknown (0) 00-0000-00 rev 70 dev 0
>> HW version 1.2 S/N SAL1248BSQ5
>> Test hist: 0x00 RMA#: 00-00-00 RMA hist: 0x00
>> DIAG: Test count: 0x00000000 Test results: 0x00000000
>> FRU: Linecard/Module: GSR16-ALRM=
>> MBUS Agent Software version 2.68 (RAM) (ROM version is 3.66)
>>
>>
>>
>>
>> sh gsr
>> Slot 0 type = Modular SPA Interface Card
>> state = IOS RUN Line Card Enabled
>> subslot 0/0: SPA-1X10GE-L-V2 (0x50C), status is ok
>> subslot 0/1: Empty
>> subslot 0/2: Empty
>> subslot 0/3: Empty
>> Slot 5 type = Modular SPA Interface Card
>> state = IOS RUN Line Card Enabled
>> subslot 5/0: SPA-2XOC48POS/RPR (0x46F), status is ok
>> subslot 5/1: SPA-5X1GE-V2 (0x50A), status is ok
>> subslot 5/2: Empty
>> subslot 5/3: Empty
>> Slot 6 type = Modular SPA Interface Card
>> state = IOS RUN Line Card Enabled
>> subslot 6/0: SPA-4XT3/E3 (0x40B), status is ok
>> subslot 6/1: SPA-4XT3/E3 (0x40B), status is ok
>> subslot 6/2: SPA-8XOC3-POS (0x505), status is ok
>> subslot 6/3: SPA-8XOC3-POS (0x505), status is ok
>> Slot 7 type = Performance Route Processor
>> state = ACTV RP IOS Running ACTIVE
>> Slot 8 type = Performance Route Processor
>> state = STBY RP IOS Running STANDBY
>> Slot 9 type = Modular SPA Interface Card
>> state = IOS RUN Line Card Enabled
>> subslot 9/0: SPA-1X10GE-L-V2 (0x50C), status is ok
>> subslot 9/1: Empty
>> subslot 9/2: Empty
>> subslot 9/3: Empty
>> Slot 14 type = Modular SPA Interface Card
>> state = IOS RUN Line Card Enabled
>> subslot 14/0: SPA-2XOC48POS/RPR (0x46F), status is ok
>> subslot 14/1: SPA-5X1GE-V2 (0x50A), status is ok
>> subslot 14/2: Empty
>> subslot 14/3: Empty
>> Slot 15 type = Modular SPA Interface Card
>> state = IOS RUN Line Card Enabled
>> subslot 15/0: SPA-4XOC12-POS (0x507), status is ok
>> subslot 15/1: SPA-8XOC3-POS (0x505), status is ok
>> subslot 15/2: SPA-4XT3/E3 (0x40B), status is ok
>> subslot 15/3: Empty
>> Slot 16 type = Clock Scheduler Card OC192 Dual Priority
>> state = Card Powered
>> Slot 17 type = Clock Scheduler Card OC192 Dual Priority
>> state = Card Powered PRIMARY CLOCK
>> Slot 18 type = Switch Fabric Card 16XOC192
>> state = Card Powered
>> Slot 19 type = Switch Fabric Card 16XOC192
>> state = Card Powered
>> Slot 20 type = Switch Fabric Card 16XOC192
>> state = Card Powered
>> Slot 24 type = Alarm Module(16)
>> state = Card Powered
>> Slot 25 type = Alarm Module(16)
>> state = Card Powered
>> Slot 27 type = Bus Board(16)
>> state = Card Powered
>> Slot 28 type = Blower Module(16)
>> state = Card Powered
>> Slot 29 type = Blower Module(16)
>> state = Card Powered
>>
>>
>> Thanks and Regards
>> J.Daniels
>> _______________________________________________
>> cisco-nsp mailing list cisco-nsp [at] puck
>> https://puck.nether.net/mailman/listinfo/cisco-nsp
>> archive at http://puck.nether.net/pipermail/cisco-nsp/
>>
>
>
_______________________________________________
cisco-nsp mailing list cisco-nsp [at] puck
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/
|
