souphonh at laopdr
Feb 1, 2006, 6:40 PM
Post #2 of 9
(3414 views)
Permalink
|
Dear All,
I am using 7206, which has specs as describe on show version below:
pppoe_ras#sh version
Cisco IOS Software, 7200 Software (C7200-JS-M), Version 12.4(3), RELEASE
SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by Cisco Systems, Inc.
Compiled Fri 22-Jul-05 09:12 by hqluong
ROM: System Bootstrap, Version 12.1(20000710:044039) [nlaw-121E_npeb 117],
DEVELOPMENT SOFTWARE
BOOTLDR: 7200 Software (C7200-BOOT-M), Version 12.0(24)S5, EARLY DEPLOYMENT
RELEASE SOFTWARE (fc1)
pppoe_ras uptime is 16 hours, 59 minutes
System returned to ROM by reload at 09:49:37 UTC Wed Feb 1 2006
System image file is "disk0:c7200-js-mz.124-3.bin"
Cisco 7206 (NPE225) processor (revision A) with 245760K/16384K bytes of
memory.
Processor board ID 10860270
R527x CPU at 262MHz, Implementation 40, Rev 10.0, 2048KB L2 Cache
6 slot midplane, Version 1.3
Last reset from power-on
Number of Fast PAs = 3
Number of Fast+Medium PAs = 4
Total number of PA bandwidth points consumed = 620
Please refer to the following document "Cisco 7200 Series Port
Adaptor Hardware Configuration Guidelines" on CCO <www.cisco.com>,
for c7200 bandwidth points oversubscription/usage guidelines.
4 Ethernet interfaces
2 FastEthernet interfaces
2 Serial interfaces
125K bytes of NVRAM.
62976K bytes of ATA PCMCIA card at slot 0 (Sector size 512 bytes).
4096K bytes of Flash internal SIMM (Sector size 256K).
Configuration register is 0x2102
I am using it as PPPoE NAS. It operated only for about 27 days, and then
crashed. The power is still on, but I cannot access to the box via console
or FastEthernet port. However, when I switch off the power and switch on
again, the box can operate normally. I am not sure what the source of the
problem is. Anyone has ideas about it? The following is router's
configuration:
Current configuration : 3469 bytes
!
version 12.4
service timestamps debug uptime
service timestamps log uptime
service password-encryption
!
hostname pppoe_ras
!
boot-start-marker
boot-end-marker
!
enable secret 5 xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
enable password 7 xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
!
aaa new-model
!
!
aaa authentication ppp polpppoe group radius local
aaa authorization network polpppoe group radius
aaa accounting exec polpppoe start-stop group radius
aaa accounting network polpppoe start-stop group radius
!
aaa session-id common
!
resource policy
!
ip subnet-zero
no ip source-route
!
!
ip cef
!
!
no ip bootp server
vpdn enable
!
async-bootp dns-server 203.137.130.1 203.137.130.2
!
!
!
!
!
!
!
!
!
!
!
!
username root password 7 xxxxxxxxxxxxxxxxxxxxxxxxxx
!
!
!
bba-group pppoe global
virtual-template 11
sessions auto cleanup
!
!
interface Loopback0
ip address 203.137.140.1 255.255.252.0
!
interface FastEthernet0/0
ip address 202.137.130.17 255.255.255.0
no ip unreachables
no ip proxy-arp
no ip mroute-cache
duplex full
!
interface Serial1/0
no ip address
shutdown
dsu bandwidth 44210
framing c-bit
cablelength 10
serial restart-delay 0
!
interface Serial1/1
no ip address
shutdown
dsu bandwidth 44210
framing c-bit
cablelength 10
serial restart-delay 0
!
interface FastEthernet2/0
ip address 10.10.0.1 255.255.252.0
ip access-group 101 in
no ip unreachables
no ip proxy-arp
no ip mroute-cache
duplex full
pppoe enable
!
interface Ethernet4/0
no ip address
shutdown
duplex half
!
interface Ethernet4/1
no ip address
shutdown
duplex half
!
interface Ethernet4/2
no ip address
shutdown
duplex half
!
interface Ethernet4/3
no ip address
shutdown
duplex half
!
interface Virtual-Template11
mtu 1492
ip unnumbered Loopback0
ip access-group 101 in
no ip route-cache cef
no ip route-cache
peer default ip address pool dial-in
ppp authentication pap chap polpppoe
ppp authorization polpppoe
ppp accounting polpppoe
!
ip local pool dial-in 202.137.140.2 202.137.143.254
ip classless
ip route 0.0.0.0 0.0.0.0 202.137.130.254
!
no ip http server
!
!
access-list 101 deny tcp any any eq 69
access-list 101 deny tcp any any eq sunrpc
access-list 101 deny tcp any any range exec cmd
access-list 101 deny tcp any any lt ftp-data
access-list 101 deny udp any any eq sunrpc
access-list 101 deny tcp any any eq 135
access-list 101 deny udp any any eq 135
access-list 101 deny tcp any any eq 137
access-list 101 deny udp any any eq netbios-ns
access-list 101 deny udp any any eq netbios-dgm
access-list 101 deny tcp any any eq 139
access-list 101 deny udp any any eq netbios-ss
access-list 101 deny tcp any any eq 445
access-list 101 deny udp any any eq 445
access-list 101 deny udp any any eq echo
access-list 101 deny udp any eq echo any
access-list 101 permit ip any any
snmp-server community hello_wbb RO
snmp-server enable traps tty
no cdp run
!
!
!
radius-server host 202.137.130.5 auth-port 1812 acct-port 1813
radius-server timeout 25
radius-server key 7 xxxxxxxxxxxx
radius-server vsa send accounting
radius-server vsa send authentication
!
control-plane
!
!
!
!
dial-peer cor custom
!
!
!
!
gatekeeper
shutdown
!
!
line con 0
stopbits 1
line aux 0
stopbits 1
line vty 0 4
transport input telnet
!
!
End
Your help will be much appreciated.
Regards,
Souphonh
|
